10
Outdoor Lifestyles by Hearth & Home Technologies Inc. • Carolina-B Owner’s Manual • 4066-501 Rev. G • 7/15
G. Heat Management
Heat output can be controlled using the HI/LOW setting
on the control module. See Figure 3.3.
H. Detailed Component Operating Instruc-
tions - IntelliFire
TM
Plus
Control Module Operation
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 3.3.
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
remote. The unit should be in the OFF position during
installation, service, battery installation, fuel conversion,
and in the event that the control goes into LOCK-OUT
mode as a result of an error code. The external control
switch must be in the OFF position also.
ON Position: Appliance will ignite and run continuously
in the HI
fl
ame setting, with no adjustment in
fl
ame
output. This mode of operation is primarily used for
initial installation or power outage operation with battery
backup. The external control switch must be in the ON
position also.
REMOTE Position: Appliance will initiate commands
from an optional wired wall switch and/or one of the
optional wireless remote options. The external control
switch must be in the ON position also.
2. With the module in REMOTE mode, the
fl
ame output
can be adjusted with the HI/LO selector switch on the
module. See Figure 3.3. Note that the control module
will always ignite the fireplace on HI and remain
so for the initial 10 seconds of operation. If the HI/
LO is switched to the LO position, the
fl
ame output
will automatically drop to the lowest setting after the
fl
ame has been established for 10 seconds. After this
10-second period, the
fl
ame can be adjusted from HI
to LO with the switch.
3. The control module has a safety feature that automatically
shuts down the
fi
replace after nine hours of continuous
operation without receiving a command from the wall
switch or optional remote.
NG/LP GAS-TYPE
SELECTOR SWITCH
SELECTOR
SWITCH
WIRE LEAD FROM REGULATOR CONNECTS HERE
MODULE
HI/LOW
Figure 3.3 Control Module
Nine Hour Safety Shutdown Feature
The appliance has a safety feature that automatically
shuts down the
fi
replace after nine hours of
continuous operation without receiving a command
from the wall switch or optional remote.
WARNING! DO NOT
place combustible objects in front of
the
fi
replace. High temperatures could start a
fi
re.
WARNING! Risk of Fire or Burns!
Provide adequate
clearance for service access.
Due to high temperatures,
the appliance should be located out of traf
fi
c and away
from furniture and draperies.
F. Appliance Break-In
Initial Break-in Procedure
When you light the appliance, you may notice that it
produces heat which does have an associated odor or
smell. This appliance should be run three to four hours
on the initial start-up. Turn it off and let it cool complete-
ly. Run the appliance for an additional 12 hours. This will
help cure the products used in the paint and logs.
4. The module has the capability to recognize potential
malfunctions. If these occur, it will fail to ignite and/or
respond to a command to ignite. If it fails to ignite, turn
off the external control switch and wait
fi
ve seconds
and turn back on. If it fails to light the second time,
see Trouble Shooting guide. In this case, the module
may have gone into LOCK-OUT mode. In this state, it
will emit a RED/GREEN LED error code. To reset the
error code, switch the selector to OFF, and then back
to REMOTE or ON. If the ignition command again fails,
the module will emit an LED error code prior to going
back into LOCK-OUT mode. Contact your dealer for
service if this occurs.
Appliance ON/OFF
If an optional remote control or wall control is installed,
it should be used to control the ON/OFF function of the
appliance. Follow instructions included with the installed
control.
To operate the appliance without a wall control or remote
control, use the ON/OFF switch located on the control
box cover on the side of the appliance. See Figure 3.2.
CAUTION! Risk of Electric Shock!
Avoid touching wires
and electrical components in appliance control cavity.
