Outdoor GreatRoom Company Intrigue INT-1 Owner'S Manual Download Page 13

Page | 13 

 

Intrigue 90215 REV E 6/7/2012 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9. 

    Step 9: 

With power switch in the OFF (Center) 
position, using two wrenches, securely fasten 
the supplied gas regulator or regulator and 
hose assembly (shown)  to the threaded 
connector protruding from the bottom of the 
gas valve assembly. 

At this time, ensure 

ALL

  connections are 

securely tightened and checked for leaks. 

To install a 1lb tank

, thread tank onto 

brass fitting and hand tighten securely.  

To install other tanks

, hand tighten 

plastic collar adapter onto tank valve. 
Do not over-tighten. 

Step 12: Concealing the valve assembly and Placing the Control switch 

Your Intrigue includes a cloth bag for concealing and protecting your product’s inner workings.  

To use bag, simply open one end, slide up over the valve assembly until the top of bag is above the 
coiled aluminum gas line on the valve assembly. Pull drawstring to tighten. Secure bottom if not already 
tightened.  

The on-off switch has a built-in bracket that can be glued, screwed, or attached via hook-and-loop to 
surfaces near the control module. We suggest attaching it to the underside of your table near an 
outside edge to make for hassle-free operation. 

Hold bead, pull 
string to tighten 

Turn to the next page for lighting and operation instructions  

On/off 
switch 

Summary of Contents for Intrigue INT-1




















Reviews: