manualshive.com logo in svg

Outback GTFX2012E, Installation Manual, Page: 23 / 56

Share
Download
Outback GTFX2012E Installation Manual Download Page 23

21

AC WIRING NOTES

AC HOT OUT

•  AC hot output conductor (brown) wire 

gauge must be sized to the breakers and 
loads

.

AC NEUTRAL OUT/AC NEUTRAL IN

•  Both neutral terminals are common with 

each other within the FX. 

•  Only one neutral needs to connect at the 

terminal if a separate common neutral bus 
bar is installed.

CHASSIS GROUND

•  Both CHASSIS GROUND terminals are 

common within the FX.

•  The AC input and AC output ground 

wires can connect to these terminals, or 
one ground wire can be connected if a 
common ground bus bar is installed.

AC HOT IN  

•  The AC hot input conductor (brown) must 

be supplied through an appropriately-
sized AC branch rated circuit breaker.

•  10.0 mm

2

 (8 AWG) or larger wire is 

recommended to accommodate the FX’s 
AC transfer relay.  

13.3 mm

2

 (6 AWG) is the largest size of wire 

that can be used with the input or output 
terminals.

����������

��������������

�����������������

�����������������

�������������

���������

�

�

��

��

�

��

��

�

�

��

�

��

�

��

�

��

�

��

��

�

�

�

��

�

��

�

�

�

������������

��������

��

�

��

��

�

��

�

��

��

��

�

��

��

�

�

�

��

��

�

�

�

�

�

�

�

�

�

�

��

�

�

��

Summary of Contents for GTFX2012E

























































Reviews:

No comments