14
TRANSPORTATION
, Рiс
. E
•
Make sure there are no children or animals in the
device.
• Move and transport the device only in the un
-
loaded condition.
• It is recommended to move and place the device
in two, Pic. E-1
• Pack the device before moving it.
• When moving do not grab or pull the door or door’s
handle.
• When moving the device you cannot tilt it more than on
45 degrees. Protect the device from excessive vibration
and hits. Pic. E-2.
• Please transport the device packed and in vertical po
-
sition. Improper transportation may result in injury and
damage of the device.
POSSIBLE PROBLEMS AND SOLUTIONS
Possible problems
Possible causes
Solutions
D
evice isn’t working.
• There is no voltage in the mains.
• The cord is plugged incorrectly.
• Turn on the device.
• Check the main and the plug. If they are
working, call the service center.
Vibrating noise .
The device is in unstable position.
• Adjust the position of the device.
• Move it if necessary.
The temperature is not cold
enough
• The door is not closed firmly.
• Not enough ventilation
• Make sure the door is firmly closed.
• Clean the vents.
The compressor is operating for
a long period.
• Ambient temperature is too high.
•
The door is opened too often or
remains open.
•
Adjust the temperature of the room.
• Make sure the door is firmly closed.
Frost accumulated on the rear
side of the device.
•
There is hot or moisture food in
the device.
• High humidity of the
environment.
•
Do not place hot or unpacked products into the
device.
• Adjust the humidity in the room.
Please check the possible problems before contacting a service center.
Reversing the door,
Pic D-4
1
2
3
4
5
6
7
8
Top hinge cover
Top hinge screw
Top hinge
Cabinet plug
Bottom hinge
Door handle plug
Bottom hinge screw
Leveling leg
1.
Remove top hinge cover
1
and top hinge screws
2
which are below it. Then remove top hinge
3
.
2.
Remove cabinet plugs
4
and door handle plug
6
.
3.
Remove the door.
4.
Remove right and left leveling legs
8
.
5.
Remove the bottom hinge
5
and bottom hinge screws
7
.
6.
Install the bottom hinge
5
on the other side of the lev
-
eling legs with bottom hinge screws
7
.
7.
Install right and left leveling legs
8
. There are two
holes below the refrigerator to fit the two levelling legs.
8. Install the door.
9. Install the top hinge
3
on the other side with top hinge
screws
2
.
10.
Install top cover
1
above the top hinge and install
cabinet plugs
4
and door handle plug
6
on the other
side.
11.
Adjust the leveling legs
8
.
Note:
Don’t tilt the appliance over 45° when revising the
door as possible damage to the sealed system may occur.
CLEANING AND MAINTENANCE,
Рiс. F
• Unplug the device.
• Wash the inner parts of the device with a soft cloth and
clean water with a detergent, then wipe everything with
a cloth and clean water and wipe dry.
•
Contamination of the door gasket can cause damage
to it, so regularly clean it with a soft cloth and a small
amount of neutral detergent.
• Outer surface of the device must be cleaned with a
slightly damp or dry cloth.
• Do not rub with detergent the informational sticker in
-
side the device, because printed information can be
erased. The information is necessary for service.
•
Do not spill water on the electrical components of
the device, as well as air vents because of the dan
-
ger of electric shock.
Summary of Contents for RF0480
