5
PREPARING ThE DEvICE FOR OPERATION
Carefully remove the device and its accessories from
the box. Remove all packing materials and promotional
labels.
Be sure to keep in place the warning decals, directional
decals (if any) and the device’s serial number plate on
the body!
Wipe the heating surfaces with a damp cloth and the
body with a dry cloth.
Device cleaning recommendations Pic. C.
BEFORE FIRST USE
1.
Before the first use, grease the heating surfaces
5
and
6
with a little vegetable oil, spread it over the
entire surface, remove excess oil with a paper towel.
2. Plug in the device, the indicator light
3
will light up.
3. Leave the device in the closed position for about 5
minutes.
NOTE:
When the device is first heated, the protective
grease is removed from the surfaces, In this case, a
short-term release of a small amount of smoke and
foreign smell is possible. This is permissible and is not
a defect.
4. When the working surfaces
5
6
are heated to the
set temperature, the indicator light
3
will go out,
unplug the device.
5. Wait for the working surfaces
5
6
, to cool com-
pletely, open the device and remove the remaining
vegetable oil from the working surfaces
5
6
with a
paper napkin.
6. Wipe the device according to Pic. C.
UTILIZATION
1.
Place the device on a flat, heat-resistant surface.
Unwind the power cord
7
completely. Do not
place the device directly under an outlet.
2. Lightly oil the working surfaces
5
6
with vegeta-
ble oil and close the device.
3. Connect the device to a power supply with ground-
ing. After switching on, the red indicator
3
will light
up.
4. When the working surfaces
5
6
are heated to the
set temperature, the heating indicator
3
will go
out, you can start cooking.
5. Grasp the handle
2
and open the device.
6. Place food carefully on the lower working surface
6
, beware of burns from possible splashes of fat
or juice from food. Lower the handle
2
and press
down on the food a little.
NOTE:
•
Beware of steam escaping from gaps between
working surfaces. Be careful not to place your
hands or place other exposed areas of your body
close to the working surfaces.
•
During operation, the working surfaces and the
body of the device become very hot; in order to
avoid burns, do not touch hot surfaces, Pic.A.
7. After the food is cooked, grasp the handle
2
and
raise the top working surface
5
.
8. Place cooked food on a suitable dish using wood or
heat-resistant kitchen utensils.
9. Close the device. When the indicator light
3
goes
out, you can continue cooking.
10. The heating indicator
3
may go out during cook-
ing. This indicates that the required temperature is
being maintained.
11. After every preparation, lightly grease the working
surfaces
5
6
with oil if necessary.
12. The cooking time depends on the food used.
You can check the readiness of the food at any
time by lifting the cover. Be careful not to get
hot air or grease splashes on your skin.
Do not use sharp objects as this may dam-
age the non-stick coating, Pic. A.
13.
To turn off the device or stop the operation, unplug
the device. The heating indicator
3
will go out.
14. Allow the grill to cool completely before cleaning.
•
Do not use the device to prepare frozen
food - defrost food before cooking. Do not
use the grill to defrost food.
•
Take out the food immediately after cook-
ing; if the food is left in the switched-on
device for a long time, it may catch fire.
CLEANING AND MAINTENANCE,
PIC. C
•
Unplug the device and let it cool before cleaning.
•
Clean the working surfaces
5
6
and wipe them with a
damp cloth, then wipe dry.
•
Burnt food residues must be removed while still warm
with a damp cloth.
•
Wipe the body of the device
1
with a slightly damp
cloth.
•
Never immerse it in water because of the
danger of electric shock.
•
After cleaning, let the device dry.
•
Do not use a brush or other rough objects or abrasive
materials when cleaning to avoid damaging the non-
stick coating.
•
Never wash the device in a dishwasher.
STORAGE
1. Before storing the grill, clean the working surfaces
5
6
and the device body
1
.
2.
For easy storage in an upright position, fix the work
-
ing surfaces
5
and
6
with the lock
4
.
3. Place the device into a cool dry place out of the
reach of children and people with disabilities.
Summary of Contents for EG0850
