Otec ECO-mini wet Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 23

background image

English - 15 -

7.3. Compounds and their application

In general the compound SC 5 is used in the

Eco-mini „wet“

.

The compound SC 5 keeps the work-pieces clean and corro-
sion-free while grinding. Also, the sharpness of the chips is re-
tained, by using this compound.
SC 5 should be mixed with water as per the following instruc-
tions:
Add 0.5 liters of the compound SC 5 to 10 liters of water.

7.4. Processing examples

7.4.1. How to process jewelry straight from the casting

When you want to process jewelry straight from the casting, the
grinding should be done in two steps:

·

Fill the work-container with approximately 1,5 liters blue

plastic chips PO 10 (pyramids) .

·

Select the processing time by turning the timer clockwise.

The machine will now start.

·

Processing time to grind gold and silver: 2-3 hours

·

Processing time to grind platinum, titanium and

stainless steel: 6-12 hours

·

The machine will switch off automatically after the time set

has expired.

·

Unload the work-container completely and separate the blue

chips from the work-pieces.

·

Fill the work-container with the white cones KX 10.

«
...
13
14
15
16
17
...
»

Summary of Contents for ECO-mini wet
























Reviews:

No comments

Related manuals for ECO-mini wet

Brand: ACDC Pages: 4

Brand: CAMAG Pages: 40

Brand: Fayat Group Pages: 50

Brand: Halyard Pages: 88

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Latham Pages: 4

Brand: SafeWaze Pages: 23

Brand: Cuisinart Pages: 159

DJ Laptop stand +tray

Brand: Power Dynamics Pages: 3

Brand: Cooper Pages: 10

Brand: Korg Pages: 32

Sportsman EXG 14/12

Brand: M&R Pages: 98

Brand: siat Pages: 102

Brand: Leica Pages: 36

Brand: Eleiko Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands