manualshive.com logo in svg

OTE Speedport Entry 2i, Maintenance Management Manual

Share
Download
OTE Speedport Entry 2i Maintenance Management Manual Download Page 17

SJ-20162405182123-002|2016-05-24 (R2.0) 

 

 

 

 

3-1

 

 

 

 

 

Chapter 3. 

Configure the 

Internet 

 

 

 

Table of Contents 

Check the DSL Status

 ............................................................................................................ 

3-1

 

Configure the WAN

 ....................................................................................................................... 

3-2

 

Configure the Ethernet WAN Switch

 .................................................................................. 

3-10

 

Configure the QoS

................................................................................................................. 

3-10

 

Configure the Security

 .......................................................................................................... 

3-17

 

Configure the Parental Controls

 .......................................................................................... 

3-29

 

Configure the DDNS

 ............................................................................................................. 

3-30

 

Configure the SNTP

 .............................................................................................................. 

3-31

 

Configure the Port Binding

 ................................................................................................... 

3-32

 

Configure the Dynamic Routing

 .......................................................................................... 

3-33

 

Configure the Multicast

 ......................................................................................................... 

3-34

 

 

3.1.

 

Check the DSL Status 

The section describes the status of  DSL. 

 

Steps 

1.  On the main page of the Speedport Entry 2i, select Internet > Status > DSL to go 

to the DSL page. 

The page is shown in 

Figure  3-1

. 

 

Figure 3-1 DSL  Status

 

 

 

 

Summary of Contents for Speedport Entry 2i




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands