background image

Before first use

Remove any packaging and promotional material from your kettle and position it on a 

stable, secure, dry and level work surface away from the edge.
Before connecting to a power source, make sure your mains supply voltage is the same 

as the one indicated on the appliance. Connect the plug to a suitable power outlet and 

make sure that the power cord does not overhang the work surface. Excess power cord 

can be stored in the power base.  
Remove the kettle from the power base and open the lid. Fill your kettle to the maximum 

mark and close the lid.
Place your kettle back onto the power base. Switch your kettle on, allow it to boil 

then discard the water. Repeat twice. This will remove any residue left over from the 

manufacturing process. 

Using your kettle

1.   To fill the kettle, remove it from the power base and lift the lid. Alternatively, the kettle 

may be filled through the pouring spout.

2.   Fill the kettle with the desired amount of water. Always fill the kettle between the 

minimum and maximum marks. Too little water will result in the kettle switching off 

before the water has boiled.

  CAUTION: Do not fill the kettle over the maximum level, as water may spill out of the 

spout when boiling.

3.   Push the lid closed firmly until it locks into position.
4.   Place the kettle on the power base and connect the plug into a 220v power outlet. 

Turn the power ON.

5.   Press the ON/OFF button downwards at the base of the kettle. The boiling ring 

around the base of the kettle will illuminate to indicate the kettle is heating. The kettle 

will switch off automatically once the water has boiled.

  NOTE: Ensure that the ON/OFF switch is clear of obstructions and the lid is firmly 

closed. The kettle will not turn off if the ON/OFF switch is constrained or if the lid 

is left open. Do not remove the kettle from the power base while water is heating. 

You cannot switch on the kettle immediately after a boil cycle. There is a minimum 

6-second break between cycles.

6.   Lift the kettle from the power base and pour the water.
  NOTE: Use caution when pouring the water from your kettle, as boiling water will 

scald.

7.   The kettle may be stored on the power base while not in use. The kettle will not re-

boil until the ON/OFF switch is pressed downward.

  NOTE: Ensure the power is turned off at the power outlet when the kettle is not 

in use. Should you accidentally allow the kettle to operate without water, boil-dry 

protection will automatically switch it off. If this occurs, allow the kettle to cool before 

filling with cold water and re-boiling.

English - 4

Summary of Contents for BVSTKT4510B

















Reviews: