background image

TV144BG

TV STAND

ASSEMBLY INSTRUCTIONS

IMPORTANT NOTE:

1.  Use hand tools only for assembly as power tools may 

cause damage

2.  Carefully remove any staples used for packaging.
3.   Phillips Screwdriver also needed for assembly (not provided)

Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.

STEP 1

  Attach one Suction Cup (8) to each Glass Support (9). Secure one Glass Support (9) to each Front Leg (3) using one Extra Small Sllen Screw 

(14) for each Glass Support (9). Secure two Glass Supports (9) to Back Panel (4) using one Small Phillip Screw (12) for each Glass Support (9). 

FULLY 

TIGHTEN ALL SCREWS

,

FULLY TIGHTEN ALL EXTRA SMALL ALLEN SCREWS (14) USING ALLEN WRENCH (22). 

STEP 2

  With Glass Supports (9) facing inwards, secure both Front Legs (3) to bottom of Top Panel (1) using four Small Allen Screws (13) for each 

Front Leg (3). Insert two Cam Lock Studs (11) into bottom of Top Panel (1), with Glass Supports (9) facing inward, align and secure Back Panel (4) to Top Panel 
(1) using two Cam Locks (10).  

FULLY TIGHTEN ALL SMALL ALLEN SCREWS (13) USING ALLEN WRENCH (23), 

FULLY TIGHTEN ALL CAM LOCKS (10). 
STEP 3

Carefully place Bottom Panel (2) onto assembly, secure front end of Bottom Panel (2) using two Long Allen Screws (15) and two Feet (5), secure 

rear end of Bottom Panel (2) using two Long Phillips Screws (16).  Secure three Feet (5) to Bottom Panel (2) using one Medium Allen (14) for each Foot (5).

FULLY TIGHTEN ALL SCREWS. 

STEP 1

STEP 2

STEP 3

PART

QTY

1.

ª4OPª0ANEL ª                   

2.

ª"OTTOMª0ANELª                 

3.

ª&RONTª,EGª                    

4.

ª"ACKª0ANEL ª                  

5.

ª&OOTª                        

6.

ª'LASSª3HELF ª                  

7. 

0LASTICª#AP ª                  

8. 

3UCTIONª#UPª                  

9.

ª'LASSª3UPPORTª                

10.

ª#AMª,OCK ª                  

11.

ª#AMª,OCKª3TUD ª              

12.

ª3MALLª0HILLIPSª3CREW ª          

13.

ª3MALLª!LLENª3CREWª            

14.

ª%XTRAª3MALLª!LLENª3CREW ª       

15.

ª-EDIUMª!LLENª3CREWª          

16. 

,ONGª!LLENª3CREWª             

17. 

,ONGª0ILLIPSª3CREWª            

18. 

!NCHORª                     

19. 

.YLONª3TRAPª                 

20. 

,ONGª7ALLª3CREWª             

21. 

3HORTª3TRAPª3CREWª            

22. 

-ª!LLENª7RENCHªNOTªSHOWN ª   

23. 

-ª!LLENª7RENCHªNOTªSHOWN ª   

STEP 4

STEP 4

Cover Cam Lock (10) holes on rear of Top Panel (1) using two Plastic Caps (7). Carefully slide Glass Shelf (6) onto Glass Supports (9).

STEP 5: ANTI-TIPPING STRAP

Attach Nylon Strap (19) to rear of Back Panel (4) using Short Strap Screw (21). Place TV Stand in desired location, carefully drill a ¼ pilot hole into wall, gently 
tap Anchor (18) into pilot hole. Place TV Stand into position, secure Nylon Strap (19) to wall using one Long Wall Screw (20).

ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING TV STAND.

TV144BG

TV STAND

ASSEMBLY INSTRUCTIONS

STEP 5

© Office Star Products September 2008

Reviews: