TV0860FBK
60” TV STAND w/ SIDE FOLDING CONSTRUC
TION
ASSEMBLY INSTRUCTIONS
© Office Star Products April 2012
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1
Fully extend the Folding Frame (2), Place Folding Frame (2) top down on a soft surface,
STEP 2
Insert Bottom Panel (6) into Folding Frame (2), hold Bottom Panel (6) up with finished side down, secure using six Wood Screws (8).
SEE DETAIL A, FULLY TIGHTEN SCREWS.
STEP 3
Turn assembly to the upright position, Insert two Wooden Dowels (10) into each end of both Dividers (3), align and slide Dividers (3)
into holes of Folding Frame (2), also insert two Wooden Dowels (10) into Folding Frame (2)
SEE DETAIL B.
IMPORTANT NOTE:
1. Use hand tools only for assembly as power tools may
cause damage
2. Carefully remove any staples used for packaging.
STEP 1
STEP 3
STEP 4
STEP 5
STEP 6
1
PART QTY
1. Top . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Folding Frame . . . . . . . . . . . . . . . . 1
3. Divider . . . . . . . . . . . . . . . . . . . . . . 2
4. Small Adjustable Shelf . . . . . . . . . . 2
5. Large Adjustable Shelf . . . . . . . . . 1
6. Bottom Panel . . . . . . . . . . . . . . . . . 1
7. Center Leg . . . . . . . . . . . . . . . . . . . 2
8. Wood Screw . . . . . . . . . . . . . . . . 16
9. Small Screw . . . . . . . . . . . . . . . . . . 2
10. Wooden Dowel . . . . . . . . . . . . . 10
11. Metal Knob . . . . . . . . . . . . . . . . . 2
12. Shelf Pin . . . . . . . . . . . . . . . . . . 12
13. Allen Wrench . . . . . . . . . . . . . . . . 1
Phillips Screwdriver also needed for
assembly (not provided)
DETAIL B
DETAIL C
DETAIL F
DETAIL G
13
7
9
12
8
8
8
TV0860FBK
60” TV STAND w/ SIDE FOLDING CONSTRUC
TION
ASSEMBLY INSTRUCTIONS
STEP 4
Carefully place Top (1) onto assembly, secure using six Wood Screws (8)
SEE DETAIL C, FULLY TIGHTEN SCREWS.
STEP 5
Carefully turn assembly top down on a soft surface,
Secure Dividers (3) using four Wood Screws (8),
SEE DETAIL D
, screw in both Center
Legs (7) to bottom of assembly,
SEE DETAIL E. FULLY TIGHEN SCREWS.
SEE DETAIL G
, Screw in both Center Legs (10) to bottom of assembly,
SEE DETAIL H. FULLY TIGHEN SCREWS.
STEP 6
Insert Shelf Pins (12) into assembly, place both Small Adjustable Shelves (4) and Large Adjustable Shelf (5) onto Shelf Pins (12).
Secure one Metal Knob (11) to each door front using one Small Screw (9) for each Metal Knob (11),
SEE DETAIL F.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING TV STAND.
DETAIL D
3
DETAIL A
STEP 2
2
11
6
10
3
DETAIL E
13
