background image

TABLE OF CONTENTS

PART A - OPERATION AND MAINTENANCE .............................................................................. 5

1. Safety Information .................................................................................................................... 5

2. General Information .................................................................................................................. 6

2.1 Specifications .................................................................................................................. 6
2.2  Zone Heating and How to Make it Work for You ................................................................11
2.3  The Benefits of Low Emissions and High Efficiency ...........................................................11
2.4  The SBI Commitment to You and the Environment ............................................................11

3. Fuel ......................................................................................................................................... 12

3.1  How to Prepare or Buy Good Firewood ............................................................................13

4. Operating Your Wood fire ....................................................................................................... 15

4.1  Cold Hand ......................................................................................................................16
4.2  Using a Blower ...............................................................................................................16
4.3  Wood Storage in the Pedestal..........................................................................................17

5. Burning Wood Efficiently ....................................................................................................... 17

5.1  First Use.........................................................................................................................17
5.2  Lighting Fires ..................................................................................................................18
5.3  Maintaining Wood Fires ...................................................................................................19
5.4  Building Different Fires for Different Needs ........................................................................21

6. Maintenance ........................................................................................................................... 23

6.1  Wood fire .......................................................................................................................23
6.2  Glass Door .....................................................................................................................24
6.3 Door ..............................................................................................................................26
6.4  Chimney Maintenance .....................................................................................................29

PART B - INSTALLATION ............................................................................................................ 30

7. Safety Information and Standards ......................................................................................... 30

7.1  Regulations Covering Wood fire Installation ......................................................................30

8. Clearances to Combustible Material ..................................................................................... 31

8.1  Certification Label ...........................................................................................................31
8.2  Clearances to Walls and Ceiling .......................................................................................31
8.3  Floor Protector ...............................................................................................................32
8.4  Reducing Wall and Ceiling Clearances Safely ....................................................................32

9. The Venting System ................................................................................................................ 34

9.1 General  .........................................................................................................................34
9.2  Suitable Chimneys ..........................................................................................................34
9.3  Minimum Flue Height .......................................................................................................35
9.4  The Relationship Between the Chimney and the House .....................................................36
9.5  Installing the Flue Connector ...........................................................................................37

Summary of Contents for INSPIRE 2000

















































Reviews: