background image

The Sentry Xpress 4.0 micro processor is manufactured by the

Orton Ceramic Foundation and displays the CE mark.

Hr./Min.

When Lit

HIGHER

°C

°F

When Off
When Lit

START/

STOP

LOWER

Program

Review

Run

M I C R O P R O C E S S O R

TM

SENTRY

Xpress

4.0

Enter

Program

Skip Seg.

Add Hold

Change Temp.

T/C Offset

Alarm

Delay

Review

1

START/STOP Key

Starts and stops a firing.

Press after each

programming step. It works like the

Enter key on a computer.

Down Arrow Key

From

press

. The program

you have selected will ap-

pear one step at a time.

When

appears,

press

. Page 4

From

press

.

Enter delay time. Press

. Page 4

During firing, press

. The program you

entered will appear one

step at a time. Page 4

Indicator

Lights

Temperature Display

Tempera-

ture display is in °F.

Temperature display is in °C.
See page 13 for instructions

on selecting °F and °C.

Time Display

: Sepa-

rates hours from minutes. Ex-

ample: Display shown above

is 1 hour and 30 minutes.

°C Display Dot

Cone Fire/Ramp-Hold Version

°F

°C

Sentry Xpress

Digital Temperature Controller

IM-222/8-07

Light is

on during pro-

gramming.

Light is

on during pro-

gram review.

Light

blinks during firing.

Up Arrow Key

From

press

. Press

to select Cone-Fire or

Ramp-Hold. Pages 6, 8

During a

Ramp-Hold firing, press the

.

will appear. Press

. The current segment

ramp or hold number will ap-

pear. To skip, press

again. Page 10

During a

Ramp-Hold firing, press

repeatedly until

ap-

pears. Press

. Each time

you press the

, the

hold time for the current seg-

ment will increase by 5 minutes.

Then press

.

Page 10

During a Ramp-Hold firing,

press

repeatedly until

appears. Press

.

Use the arrow keys to change

the target temperature for the

current segment. Then press

. Page 10

During a fir-

ing, press

repeatedly

until

appears. Press

. Use the arrow keys to

change the alarm temperature.

Press

. To silence the

alarm, press any key. Page 10

At the

display,

press

.

will ap-

pear. Use arrow keys to adjust

the controller to fire hotter or

cooler. Press

to return to

. Page 13

*These features are new with the Sentry Xpress 4.0. If your controller does

not have these features, it is an earlier controller.

Summary of Contents for Sentry Xpress 4.0





















Reviews: