Orthman 125-087-02-EN-OM Operator'S Manual Download Page 32 | Manualshive

Page: 32 / 62

Orthman 125-087-02-EN-OM Operator'S Manual Download Page 32

PREPARATION AND SETUP

DR12x2 Row Hopper Planter OM-EN

4-8

Leveling the Wings

When row units are added to the mid and outer wings,
the additional weight may cause the wings to no longer
be level with the center section. Check the levelness of
the wings over the life of the toolbar to ensure proper
performance.

Before adjusting the wings, inspect implement for
damaged or broken parts. Remove any buildup of
grease, oil, or debris.

NOTE:

Left side wing leveling procedure is shown. Right

side wing leveling procedure is similar.

1. Install the float link lock pin (1) into the float link rigid

position to lock the wing in the rigid position. The
wing fold hydraulic cylinder (2) must be partially
extended to align pin holes in the wing float link
plates (3).

ORM000128

Figure 4-9

2. Park the toolbar on a level surface in the raised

position and check the levelness of the rear toolbar
center section. This will be the reference point for
leveling the wing.

NOTE:

For the greatest accuracy, the wing row units

should have all attachments and be fully loaded
during leveling.

3. Place the level or angle-finder (4) on the top of the

wing (5) and note its levelness. Compare that
levelness to the reference taken from the center
section (6). The wing must be from 0° to +2° of level
with the center section for proper toolbar function. If
the wing angle is lower than or more than 2° of the
center section, adjust it using the following steps 4—
11.

ORM000137

Figure 4-10

DANGER

!

Avoid crushing. Failure to follow this information will
result in death or serious injury. Use appropriate stands
to support the implement.

4. Support the wing (5) with a minimum 5-ton stand (7)

and lower machine.

ORM000138

Figure 4-11

Tools

• 3-1/8 in Wrench

• 9/16 in Wrench (2 used)

• 3/4 in Wrench

• Level or angle finder

1) Float link lock pin
2) Wing fold hydraulic

cylinder

3) Wing float link plate

(2 used)

1

2

3

4) Angle-finder

6) Center section

5) Wing

5) Wing

7) Stand

6) Center section

8) Pivot point (2 used)

6

4

5

6

8

5

7

8

«
...
30
31
32
33
34
...
»

Summary of Contents for 125-087-02-EN-OM































































Reviews:

No comments