PWR1 PWR2
10/100M
Reset
LTE
Main ANT.
ETH1
WAN
ETH2 WIFI
ETH1
ETH2
LTE
AUX ANT.
Rx
Tx
Serial
WIFI ANT.
IMG-4312-MN
S
e
ri
a
l
PWR1 PWR2 PoE
10/100M
Reset
LTE
Main ANT.
ETH1
WAN
ETH2 WIFI
ETH1
P.O.E.
ETH2
LTE
AUX ANT.
Rx
Tx
Serial
WIFI ANT.
IMG-4312+-MN
S
e
ri
a
l
5
Quick Installation Guide
Version 1.5
Q
uick
I
nstallation
G
uide
PRINTED ON RECYCLED PAPER
Q I G
1907-200-M4312MNXX1-FX015
Installation
DIN-rail
Step 1 :
Slant the device and screw the Din-rail kit onto the back of the device, right in the
middle of the back panel.
Step 2 :
Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into
the rail firmly.
Dimension
Panel Layouts
Front Panel
1. LED for Power 1 module
2. LED for Ethernet ports
3. LED for WAN status
4. LED for Power 2 module
5. LED for Wi-Fi status
6. LTE antenna connector
7. Reset button
8. Ethernet ports (ETH1 as LAN port; ETH2 as
WAN port)
9. Wi-Fi antenna connector
10. Serial port
11. TX status of serial port
12. RX status of serial port
13. PoE indicator (IMG-4312+ Series only)
1. Din-rail screw holes
Introduction
IMG-4312-MN LPWAN (Low-Power Wide-Area Network) series
Gateway
with one RS-232/422/485 serial port and two 10/100Base-T(X) ports. The
device provides an IEEE802.11b/g/n Wi-Fi interface featuring a link speed
up to 150Mbps. It can be configured to connect to the Internet by dialing up
the embedded LTE CAT-M1/ CA
cellular modem. In addition, the
T NB1
-
device can transfer data to five host PCs simultaneously for backup
purposes. The
provides P.D. function on its ETH1 port
IMG-4312+-MN
which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore,
it can receive power via an Ethernet cable to save installation costs and
simplify deployment.
is an innovative product for
IMG-4312(+)-MN Series
Cloud, Internet of Things and Industry 4.0 applications. It is a perfect choice
for remote secured data collection from the factory floor (PLCs, machines,
networking devices) and environmental sensors (temperature, humidity,
noise, pollution, vibration etc.) as well as for serving control commands
coming from Cloud Platforms for changing end-devices status.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Contents
IMG-4312(+)-MN
Pictures
Number
X 1
QIG
X 1
LTE Antenna
Preparation
Before installation, make sure you have all of the package contents available and a PC
with Microsoft Internet Explorer 6.0 or later, for using web-based system management
tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure the operating
ambient temperature is compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation of the
equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Safety & Warnings
DIN-rail kit
X 1
Wall-Mount Kit
X 2
X 2
81.0
45.0
9
5
.0
30.38
22.52
26.9
40.0
5
0
.0
2
5
.3
Rear Panel
1
Top Panel
1
2
1. Terminal block
2. Wall-mount screw holes
3. SIM card slot
4. Frame ground
Wall-mount
Step 1:
Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A
total of
screws are required, as shown below.
eight
Step 2:
Use the device, with wall mount plates attached, as a guide to mark the correct locations
of the four screws.
Step 3:
Insert a screw head through middle of the keyhole-shaped aperture on the plate, and
then slide the device downwards. Tighten the screw head for added stability.
Wi-Fi Antenna
X 1
4-pin terminal block
X 1
Dust cover
X 2
13
4
7
3
1
2
8
9
DC
12
-4
8V
SIM C
ard
PW
R-1
PW
R-2
V1
-
V1
+
V2
-
V2
+
3
I N D U S T R I A L
M2M
Gateway
Industrial Cellular M2M Gateway
9
3-pin terminal block
X 1
2
9
.0
13.1
23.0
4
3
.5
8
.0
14.0
15.5
45
2
3
.0
22.3
1
0
.8
5
Ø
3
.0
Ø
5.
9
Ø
4.
0
PWR1 PWR2 PoE
10/100M
Reset
LTE
Main ANT.
ETH1
WAN
ETH2 WIFI
ETH1
P.O.E.
ETH2
LTE
AUX ANT.
Rx
Tx
Serial
WIFI ANT.
IMG-4312+-MN
S
e
ri
a
l
Unit =mm (Tolerance ±0.5mm)
DC12-48V
SIM Card
PWR-1
PWR-2
V1-
V1+
V2-
V2+
6
10
11
12
6
4
PWR1 PWR2
10/100M
Reset
LTE
Main ANT.
ETH1
WAN
ETH2 WIFI
ETH1
ETH2
LTE
AUX ANT.
Rx
Tx
Serial
WIFI ANT.
IMG-4312-MN
S
e
ri
a
l
5
4
7
3
1
2
8
9
6
10
11
12
6
PWR1 PWR2 PoE
10/100M
Reset
LTE
Main ANT.
ETH1
WAN
ETH2 WIFI
ETH1
P.O.E.
ETH2
LTE
AUX ANT.
Rx
Tx
Serial
WIFI ANT.
IMG-4312+-MN
S
e
ri
a
l
IMG-4312(+)-MN Series
IMG-4312(+)-MN Series
