ORiNG IES-2050 User Manual Download | Manualshive

Page: 22 / 36

background image

IES-2050 User’s Manual

ORing Industrial Networking Corp.

21

5.1.4 Redundancy

5.1.4.1 Fast Recovery Mode

The Fast Recovery Mode can be set to connect multiple ports to one or more switches.

The IES-2050 with its fast recovery mode will provide redundant links. Fast Recovery

mode supports 4 priorities, only the first priority will be the act port, the other ports

configured with other priority will be the backup ports.

Fast Recovery Mode interface

The following table describes the labels in this screen.

Label

Description

Active

Activate the fast recovery mode.

port

Port can be configured as 5 priorities. Only the port with highest

priority will be the active port. 1st Priority is the highest.

Apply

Click “

Apply

” to activate the configurations.

5.1.4.2 O-Ring

O-Ring is one of the most powerful Redundant Ring technology in the world. The

recovery time of O-Ring is less than 10 mS over 250 units of connections. It can

reduce unexpected malfunction caused by network topology change. O-Ring

technology supports three Ring topologies for network redundancy: O-Ring, Coupling

Ring and Dual Homing.

«
...
20
21
22
23
24
...
»

Summary of Contents for IES-2050





































Reviews:

No comments

Related manuals for IES-2050

Brand: Magnetrol Pages: 12

Brand: Magnetrol Pages: 24

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

DKVM-16 - KVM Switch

Brand: D-Link Pages: 24

Dis-200G Series

Brand: D-Link Pages: 161

Dis-200G Series

Brand: D-Link Pages: 16

Dis-200G Series

Brand: D-Link Pages: 47

Brand: D-Link Pages: 25

DGS-3100 SERIES

Brand: D-Link Pages: 54

DGS-3100 SERIES

Brand: D-Link Pages: 220

Brand: D-Link Pages: 24

DGS-1248T - Switch

Brand: D-Link Pages: 52

DGS-1216T - Switch

Brand: D-Link Pages: 42

DGS-1216T - Switch

Brand: D-Link Pages: 10

Brand: D-Link Pages: 8

Brand: D-Link Pages: 379

Brand: D-Link Pages: 240

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands