ORiNG IES-2050 User Manual Download | Manualshive

Page: 19 / 36

background image

IES-2050 User’s Manual

ORing Industrial Networking Corp.

18

5.1.2.5 Backup & Restore

You can save current EEPROM value of the switch to TFTP server, then go to the TFTP

restore configuration page to restore the EEPROM value.

Backup & Restore interface

The following table describes the labels in this screen.

Label

Description

TFTP Server IP Address

Fill in the TFTP server IP

Restore File Name

Fill the file name.

Restore

Click “

restore

” to restore the configurations.

Restore File Name

Fill the file name.

Restore

Click “

restore

” to restore the configurations.

Backup

Click “

backup

” to backup the configurations.

5.1.2.6 Upgrade Firmware

Upgrade Firmware allows you to update the switch firmware. Before updating, make

sure you have your TFTP server ready and the firmware image is on the TFTP server.

«
...
17
18
19
20
21
...
»

Summary of Contents for IES-2050





































Reviews:

No comments

Related manuals for IES-2050

Brand: KELCO Pages: 2

Brand: Gavita Pages: 12

Brand: Eaton Pages: 2

Brand: Black Box Pages: 2

SRS Lighting DTS16F-DIN

Brand: plasa Pages: 4

Brand: Extron electronics Pages: 2

A99-BAI-ACSF-UGKIT

Brand: Westell Pages: 3

Brand: Exsys Pages: 14

Brand: Harman Pages: 50

Brand: Tabs Pages: 4

Brand: ALFAtron Pages: 15

Brand: Versitron Pages: 46

Brand: DataParts Pages: 5

Brand: Edge-Core Pages: 60

Brand: steute Pages: 10

VNLW-P-1001-MV-N-W

Brand: Greengate Pages: 2

EPS-1XPB-1XPL-M1-24V

Brand: Larson Electronics Pages: 2

Brand: SWEEX Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands