manualshive.com logo in svg

ORiNG IAP-W510, User Manual, Page: 9 / 54

Share
Download
ORiNG IAP-W510 User Manual Download Page 9

IAP-W510  /  W512 

User‟s  Manual 

 

5                                                                                                ORing Industrial Networking Corp. 

4.2  100Base-T(X)/10Base-T Pin Assignments 

With  100Base-T(X)/10Base-T  cable, pins  1  and  2  are  used  for  transmitting  data,  and 

pins 3 and 6 are used for receiving data. 

 

RJ-45 Pin Assignments 

Pin Number 

Assignment 

1 

TD+ 

2 

TD- 

3 

RD+ 

4 

Not used 

5 

Not used 

6 

RD- 

7 

Not used 

8 

Not used 

 

The IAP-510 / 512 AP support auto MDI/MDI-X operation.    You can use a straight-through 

cable  to  connect  PC  and  AP.    The  following  table  below  shows  the  10Base-T/ 

100Base-T(X) MDI and MDI-X port pin outs. 

MDI/MDI-X pins assignment 

Pin Number 

MDI port   

MDI-X port 

1 

TD+(transmit) 

RD+(receive) 

2 

TD-(transmit) 

RD-(receive) 

3 

RD+(receive) 

TD+(transmit) 

4 

Not used 

Not used 

5 

Not used 

Not used 

6 

RD-(receive) 

TD-(transmit) 

7 

Not used 

Not used 

8 

Not used 

Not used 

Note:

 

“+” and “-” signs represent the polarity of the wires that make up each wire pair. 

Summary of Contents for IAP-W510























































Reviews:

No comments