manualshive.com logo in svg

ORiNG IAP-W510, User Manual, Page: 5 / 54

Share
Download
ORiNG IAP-W510 User Manual Download Page 5

IAP-W510  /  W512 

User‟s  Manual 

 

1                                                                                                  ORing Industrial Networking Corp. 

G

etting to Know Your Access Point 

 

1.1  About the ORing Access Point 

IAP-W510  /  W512  are  reliable  IEEE802.11a/n  WLAN 

Access  Point  with  1  Ethernet  LAN  port.    It  can  be 

configured to operate in AP / Bridge / Repeater / AP-Client / 

Client  mode.    You  can  configure  IAP-W510  /  W512  by 

Window  Utility  or  WEB  interfaces  via  LAN  port  or  WLAN 

interface. Therefore, IAP-W510 / W512 are one of the best 

communication solutions for wireless application. 

 

1.2  Software Features   

 

High  Speed  Air  Connectivity:  WLAN  interface  support  up  to  300Mbps  link  speed 

connection 

 

Highly Security Capability: WEP/WPA/WPA2/WPA2-PSK/802.1x supported 

 

Support AP/Bridge/Repeater/AP-Client/Client Mode 

 

Secured Management by HTTPS   

 

Event Warning by Syslog, Email, SNMP Trap 

 

Support X-Roaming < 100 ms 

1.3  Hardware Features   

 

Wilder Power Inputs: 12~68 VDC 

 

10/100Base-T(X) Ethernet port   

 

Casing: IP-67 

 

Dimensions(W x D x H) : 162 mm(W)x 102 mm( D )x 58 mm(H) for IAP-W510; 

162 mm(W)x 102 mm( D )x 48 mm(H) for IAP-W512 

 

Operating Temperature: -30 to 70

o

C 

 

Storage Temperature: -30 to 85

o

C 

 

Operating Humidity: 100% non-condensing 

 

Summary of Contents for IAP-W510























































Reviews:

No comments