2
Checking the product
This chapter explains the items you should check, as well as the names and functions
of each part.
■
■
Package contents
Verify that the items listed below are included. Report any missing or damaged items to
the branch or sales office from which you purchased the product.
Motor ...................................................................... 1 unit
The figure shows an example of the combination type.
Combination type: With a gearhead
Mounting screw set ............................................. 1
Supplied with the combination type.
①
Hexagonal socket head screw: 4 pieces
③
Spring washer: 4 pieces
② P
lain washer: 4 pieces
④
Parallel key: 1 piece
（
200W, 300W, and 400W types are fixed to the output shaft
）
Instructions and Precautions for Safe Use ...... 1 copy
■
■
Model
Verify the model number of the purchased product against the number shown on
the package label. Check the model number of the motor and gearhead against the
number shown on their nameplates, respectively.
o
in the model name indicates a number representing the gear ratio.
in the model name indicates
A
(no machining) or
AC
(shaft flat) for the round
shaft type.
z
Combination type • parallel shaft gearhead
Output
power
Combination motor model
Motor model
Gearhead model
30 W
BLM230-
o
B
BLM230-GFV2
GFV2G
o
60 W
BLM460S-
o
B
BLM460S-GFV2
GFV4G
o
120 W
BLM5120-
o
B
BLM5120-GFV2
GFV5G
o
200 W
BLM6200S-
o
B
BLM6200S-GFV
GFV6G
o
300 W
BLM6300S-
o
B
BLM6300S-GFV
400 W
BLM6400S-
o
B
BLM6400S-GFV
z
Round shaft type
Output
power
Motor model
30 W
BLM230-
2
60 W
BLM260-
2
120 W
BLM5120-
2
200 W
BLM5200-
300 W
BLM5300-
400 W
BLM5400-
■
■
Names and functions of parts
Output
shaft
Mounting hole
(4 locations)
Motor cable
Gearhead
Motor
Protective Earth
Terminal
Be sure to ground.
Installation
This section explains the installation method of a load in addition to the installation
location and installation method of the product.
■
■
Installation location
Install the product in a well-ventilated location that provides easy access for
inspection.
•
Inside an enclosure installed indoors (provide a ventilation hole)
•
Operating ambient temperature: 0 to +40 °C (+32 to +104 °F) (non-freezing)
•
Operating ambient humidity: 85% or less (non-condensing)
•
Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas) or liquid
•
Area not exposed to direct sun
•
Area free of excessive amount of dust, iron particles or the like
•
Area not subject to splashing water (rain, water droplets), oil (oil droplets) or other
liquids
•
Area free of excessive salt
•
Area not subject to continuous vibration or excessive shocks
•
Area free of excessive electromagnetic noise (from welders, power machinery, etc.)
•
Area free of radioactive materials, magnetic fields or vacuum
•
Altitude Up to 1000 m (3300 ft.) above sea level
■
■
Installation method
z
Installing the combination type • parallel shaft gearhead
Secure the motor through four mounting holes using the supplied mounting screw
set. Do not leave a gap between the motor and mounting plate.
Supplied
Motor
Gearhead
L2
L1
Model
Gear ratio
Hexagonal socket head screw (Material:
Stainless steel)
Tightening
torque
Screw size L1 [mm (in.)] L2 [mm (in.)]
BLM230
5
to
20
M4
50 (1.97)
6 (0.24)
1.4 N·m
(12.3 lb-in)
30
to
100
55 (2.17)
7 (0.28)
200
60 (2.36)
7 (0.28)
BLM460S
5
to
20
M6
60 (2.36)
8 (0.31)
5.0 N·m
(44 lb-in)
30
to
100
65 (2.56)
8 (0.31)
200
70 (2.76)
8 (0.31)
BLM5120
5
to
20
M8
70 (2.76)
11.5 (0.45)
12.0 N·m
(106 lb-in)
30
to
100
85 (3.35)
13.5 (0.53)
200
90 (3.54)
12.5 (0.49)
BLM6200S
BLM6300S
∗1
BLM6400S
∗2
5
to
20
M8
85 (3.35)
11 (0.43)
12.0 N·m
(106 lb-in)
30
,
50
100 (3.94)
14 (0.55)
100
,
200
110 (4.33)
10 (0.39)
∗1
The gear ratio of the
BLM6300S
is 5:1 to 100:1.
∗2
The gear ratio of the
BLM6400S
is 5:1 to 50:1.
z
Removing/Installing the gearhead
See the following steps to replace the gearhead or to change the cable position.
1.
Removing the gearhead
Remove the hexagonal socket head screws assembling the motor and gearhead
and detach the motor from the gearhead.
•
Assembly hexagonal socket head screw
Model
Screw size
Tightening torque
BLM230
BLM460S
M2.6
0.4 N·m
(3.5 lb-in)
BLM5120
BLM6200S
BLM6300S
BLM6400S
M3
0.6 N·m
(5.3 lb-in)
