HM-9208-3
O P E R A T I N G M A N U A L
Torque Motors
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and
safety precautions.
•
Please read it thoroughly to ensure safe operation.
•
Always keep the manual where it is readily available.
1
Introduction
Before using the motor
Only qualified personnel should work with the product.
Use the product correctly after thoroughly reading the section “Safety
precautions”.
Should you require the inspection or repair of internal parts, contact the
Oriental Motor office where you purchased the product.
The product described in this manual has been designed and manufactured
for use as an internal component for general industrial equipment, and must
not be used for any other purpose. Oriental Motor Co., Ltd. is not responsible
for any damage caused through failure to observe this warning.
If you have purchased a torque motor and power controller package, also
refer to the operating manual for Power Controller
TMP-1
.
Standard and CE Marking
Motors are recognized by UL and certified by CQC. Recognized name and
certified name are motor model name.
Voluntary display of the CE mark conforming to the Low Voltage Directives.
Standards
UL 1004, UL 2111, CSA C22.2 No.100, CSA C22.2 No.77, GB 12350
Standards File No.
UL File No.E64197, CQC
Applications for Standard
EN 60034-1, EN 60034-5, EN 60664-1, EN 60950-1
A Running Heating Test and a Locked-Rotor Test has been conducted with a
aluminum radiation plate of size indicated below. For the motor with a
gearhead, tests has been conducted with a gearhead instead of the radiation
plate.
First number
in motor
name
Size [mm (in.)]
Thickness
[mm (in.)]
Material
2
115 × 115 (4.53 × 4.53)
3
125 × 125 (4.92 × 4.92)
4
135 × 135 (5.31 × 5.31)
5
165 × 165 (6.50 × 6.50)
5 (0.20)
Aluminum
Installation conditions
Overvoltage category II, Pollution degree 2, Class I equipment (For EN/IEC
Standards)
When the machinery to which the motor is mounted requires overvoltage
category III and pollution degree 3 specifications, install the motor in a
cabinet that comply with IP54 and connect to power supply via an isolation
transformer.
Standards for accessories
Capacitor: UL File No.E83671 (CYWT2), VDE License Nos.112847
(capacitors with a rated voltage of 250 VAC), 114747 (capacitors
with a rated voltage of 450 VAC)
Capacitor cap: UL File No.E56078 (YDTU2)
Hazardous substances
RoHS (Directive 2002/95/EC 27Jan.2003) compliant
Safety precautions
The precautions described below are intended to prevent danger or injury to
the user and other personnel through safe, correct use of the product. Use the
product only after carefully reading and fully understanding these
instructions.
Warning
Handling the product without observing the
instructions that accompany a “Warning” symbol
may result in serious injury or death.
Caution
Handling the product without observing the
instructions that accompany a “Caution” symbol
may result in injury or property damage.
Note
Note
The items under this heading contain important
handling instructions that the user should observe
to ensure safe use of the product.
Warning
•
Do not use the product in explosive or corrosive environments, in the
presence of flammable gases, locations subjected to splashing water, or
near combustibles. Doing so may result in fire, electric shock or injury.
•
Assign qualified personnel the task of installing, wiring,
operating/controlling, inspecting and troubleshooting the product. Failure
to do so may result in fire, electric shock or injury.
•
Do not transport, install the product, perform connections or inspections
when the power is on. Always turn the power off before carrying out these
operations. Failure to do so may result in electric shock.
•
Turn off the power in the event the overheat protection device (thermal
protector) is triggered. Failure to do so may result in injury or damage to
equipment, since the motor will start abruptly when the overheat
protection device (thermal protector) is automatically reset.
•
To prevent the risk of electric shock, use the motor for
class I equipment only.
Motore zur Verwendung in Geräten der Schutzklasse I.
•
Install the motor in an enclosure in order to prevent electric shock or
injury.
•
Install the motor so as to avoid contact with hands, or ground it to prevent
the risk of electric shock.
Die Gehäuse der Motore sind mit einer Schraube und Zahnscheibe sicher
mit dem geerdeten Gehäuse des Gerätes zu verbinden.
.
•
Keep the input-power voltage within the specification to avoid fire and
electric shock.
•
Connect the cables securely according to the wiring diagram in order to
prevent fire and electric shock.
•
Do not forcibly bend, pull or pinch the lead wires. Doing so may result in
fire and electric shock.
•
Be sure to insulate the connection terminal of the capacitor. Failure to do
so may result in electric shock.
•
Turn off the power in the event of a power failure, or the motor will
suddenly start when the power is restored and may cause injury or damage
to equipment.
•
Do not touch the connection terminal of the capacitor immediately after
the power is turned off (for a period of 30 seconds). The residual voltage
may cause electric shock.
•
Do not disassemble or modify the motor. This may cause electric shock or
injury.
Caution
•
Do not use the motor beyond its specifications, or electric shock, injury or
damage to equipment may result.
•
Do not touch the motor during operation or immediately after stopping.
The surface is hot and may cause a skin burn(s).
•
Do not hold the motor output shaft or motor lead wires. This may cause
injury.
•
Keep the area around the motor free of combustible materials in order to
prevent fire or a skin burn(s).
•
To prevent the risk of damage to equipment, leave nothing around the
motor that would obstruct ventilation.
•
To prevent bodily injury, do not touch the rotating parts (output shaft) of
the motor during operation.
