background image

8

*Need some help? Call 02 4574 8888 or go to 

www.oricom.com.au

Charging the Battery

1.   The signal LED Indicator on the 

Headset Receiver will blink slowly 

when the battery level is low. At this 
stage there are about 20 minutes of 
operating time before the Headset will 

switch off. Recharge the battery.

2.   Switch OFF the On/Off Switch on the 

Headset (see figure (1)). The green 
LED on the Headset should turn off.

3.   Place the headset on the Charging 

Cradle (see figure (2)). Make sure the 

charge contact touches the charge 
pins on the Charging Cradle.

4.   The Charging process starts 

automatically.

•  The LED Indicator glows red during 

charging.

•   It will glow green after the battery is 

fully charged.

WARNING:

•  The battery must not be exposed to excessive heat such as sunshine, fire 

etc.

• Do not attempt to replace the original rechargeable battery.
•  When the headsets are not in use, move the switch to the OFF position 

to avoid damaging the batteries.

•  The battery must always be fully charged before first use. An initial 3 

hours charge is required to guarantee an acceptable service life for the 

rechargeable battery. Always ensure that the Receiver is switched to 

OFF position while the battery is charging.

•  Excessive sound pressure from earphones and headsets can cause 

hearing loss.

IMPORTANT:

This unit should be operated with built-in rechargeable battery only. When 
disposing of the unit, always comply with applicable laws relating to the 

disposal of battery. Please place them in a proper disposal container to 

ensure that they are eliminated safely and in an environmentally friendly 
way.

(5)

(6)

(1)

(2)

Charging the Battery

Summary of Contents for TV7400





















Reviews: