PROJI Projection Clock
with Weather Forecast
Model: BAR369PA
User Manual
EN
INTRODUCTION
Thank you for purchasing the Oregon Scientific™ PROJI Projection
Clock with Weather Forecast (model: BAR369PA). This device
bundles precise time keeping, alarm, temperature and weather
monitoring features into a single tool you can use from the
convenience of your home. Keep this manual handy as you use your
new product. It contains practical step-by-step instructions, as well
as technical specifications and warnings you should know.
PACKAGE CONTENTS
1
Main unit
Power adapter
Remote sensor
(THN132N)
AAA batteries for main unit x 2
AA battery for remote sensor
OvERvIEW
FRONT & TOP vIEW
1
2
3
4
5
6
1.
+
- Press to increase settings, or toggle between channel 1-5
and auto-loop. Press and hold to increase rapidly in settings, or
search for the sensor for all channels in idle.
2.
SNOOZE I LIGHT
- Press to snooze an alarm or activate
the backlight and projection, press and hold until you hear a
beep to activate the projection for 5 minutes.
3. - Press to toggle between current time, calendar or
alarm 1/2 displays for 5 seconds. Press and hold to enter
setting mode.
4.
–
- Press to decrease settings, press and hold to decrease
settings rapidly.
5. Projection lens.
6.
- Press to turn on/off alarms, press and hold to enter alarm
setting mode.
REAR vIEW
1
2
3
4
5
6
1. Battery compartment.
2.
- Projection focus knob.
3.
RESET
- Press to reset the unit to default.
4.
/
PROJECTION
- Press to flip the projection content in
180°. Press and hold to toggle continuous projection on/off.
5.
RCC
– Press to turn on and search RCC signal. Press and hold
to turn off.
6. Battery compartment cover.
LCD SCREEN
1
2
3
4
5
1. Time display
2. Weather forecast display
3. Outdoor temperature display (Channel 1-5)
4. Weekday display
5. Indoor temperature display
Symbol
Description
Alarm 1 is on
Alarm 2 is on
RCC signal received
Outdoor sensor low battery
Main unit low battery
Receiving sensor signal
Outdoor sensor auto-loop function is on
Outdoor sensor channels
PROJECTION
2
1
1. Time display
2. Weather forecast display
REMOTE SENSOR (THN132N)
1. LED status indicator
2. Wall mount hole
3. Battery compartment
4.
RESET
hole
5.
CHANNEL
switch
NOTE
This package includes a 3-channel sensor. For sensor
with up to 5-channel, you may purchase additional accessory
sensors as per your own preference, for more details about
accessory sensors, please visit www.oregonscenitific.com.
GETTING STARTED
INSERT BATTERIES
1. Gently push the battery compartment cover downwards to
remove it from the main unit.
2. Insert the batteries, matching the polarities (+/-).
NOTE
Replace the batteries when
displays, or when the
display is dim.
DC POWER
Plug the power cable to the power jack and plug the power adapter
into a suitable power outlet.
NOTE
It is recommended to insert the battery as a backup power
source.
REMOTE SENSOR
The main unit can collect data from up to 5 sensors.
To set up the sensor:
1. Open the battery compartment.
2. Insert the batteries, matching the polarities (+/-).
3. Select a channel then press
RESET
.
4. Close the battery door.
5. Place the sensor within 30 m (98 ft) of the main unit using
the table stand or wall mount.
TIP
Ideal placements for the sensor would be in any location on the
exterior of the home at a height of 1.5 m (5 ft) and which can shield
it from direct sunlight or wet conditions for an accurate reading.
1.5m(5ft)
NOTE
Use alkaline batteries for longer usage and consumer
grade lithium batteries in temperatures below freezing.
SENSOR DATA TRANSMISSION
T
o search for a sensor:
Press and hold
+
.
The sensor reception icon in the remote sensor area shows
the status:
Icon
Description
Searching for sensor(s).
Sensor is found.
Cannot find sensors.
TIP
The transmission range may vary depending on many
factors. You may need to experiment with various locations to get
the best results.
CLOCK
CLOCK RECEPTION
This clock synchronizes automatically with a clock signal. Press
RCC
to turn on and search for the clock signal. The main unit is
able to receive RF clock data with different RCC signal:
Model number
Region
Signal
BAR369PA
US
WWVB
Clock signal reception indicator:
Icons
Description
Main unit is searching for
clock signal strength
(flash)
Main unit is searching for
clock signal
No clock signal
Strong RCC signal received
Weak RCC signal received
NOTE
It takes 2-10 minutes to receive the clock signal. If the
signal is weak, it could take up to 24 hours to receive a valid signal.
SET THE CLOCK MANUALLy
1. Press and hold
. The screen displays
ZONE
and the
number flashes.
2. Press once or press and hold +/- to adjust the setting. For US,
the time-zone setting is Atlantic (
A
); Mountain (
M
); Pacific (
P
);
Central (
C
); Eastern (
E
); Newfoundland (
N
).
3. Press to confirm.
4. Press once or press and hold +/- to adjust the setting for 12/24h
hour format, hour, minute, year, calendar format (month-day/
day-month), month, date, temperature unit (°C/°F) , language
and daylight saving time (DST) (ON/OFF).
5. Press to confirm each setting.
NOTE
• The language options are English (
ENG
), Spanish (
SPA
),
Italian (
ITA
), French (
FRE
) and German (
GER
).
• The RCC signal reception is on after each reset or battery
replacement.
• The daylight saving time (DST) is set to
OFF
when the RCC
is turned off, or when the time/year, month or date is changed.
• While in the setting mode, press and hold
to save the
settings and leave the setting mode.
ALARM
SETTING/ADJUSTING ALARM TIME
1. Press and hold .
2. Press once or press and hold
+
/
-
to adjust the hour and minute
setting, then press
to confirm.
3. Press
+
/
-
to toggle the weekday alarm
ON
/
OFF
, then press
to confirm.
The alarm rings only on weekdays when the setting is
ON
.
4. Repeat step 2 – 4 for alarm 2 setting.
TURN ON/OFF ALARMS:
Press
to turn on/off the alarm in sequence:
Alarm1
> Alarm 2
> Both ON
> Both OFF.
OPERATION
When the alarm rings, the backlight will flash. You may:
• Press to stop. The alarm will ring again on the next day.
• Press
SNOOZE I LIGHT
to snooze. The alarm rings again after
8 minutes.
WEATHER FORECAST
This product forecasts the next 6 hours of weather within a
19-31 mile (30-50 km) radius.
Symbol
Description
Sunny
Snowy
Cloudy
Rainy
TEMPERATURE
The current indoor temperature is always displayed in the
bottom right corner of the screen display. To receive outdoor
temperature information, you can connect up to 5 remote
sensors to the main unit:
To toggle sensor display:
Press
+
/
-
.
NOTE
When the indoor temperature is lower than -5
o
C (23.0
o
F),
the screen displays
LL.L.
When the temperature is higher than
50
o
C (122.0
o
F), the screen displays
HH.H
.
To auto-loop between sensors:
Press
+
/
-
repeatedly until
displays. The data on each sensor
displays for 3 seconds. Press
+
/
-
again turn off the auto-loop, the
icon turns off.
NOTE
The sensor displays in ascending order. If all 5 sensors
are not present, the main unit skips the absent sensor and advances
to the next present sensor.
PROJECTION
The projector displays the time and weather forecast on your
ceiling for easy viewing in a darkened room. For the optimal
projection results, place the unit within 1.5 - 2 m (5 – 6.5 ft) from
the ceiling or wall.
• Press
SNOOZE I LIGHT
to activate the backlight and
projection for 5 seconds.
• Press and hold
SNOOZE I LIGHT
until you hear a beep to
activate the projection for 5 minutes
• Press
/
PROJECTION
to flip the projection content by 180°.
• Press and hold
/
PROJECTION
to toggle the continuous
projection on/off.
• Adjust the focus (1.5 -2 m) using the focus knob.
NOTE
The continuous projection function is disabled when the
main unit is not connected to the power adapter.
PRECAUTIONS
• Do not subject the unit to excessive force, shock, dust,
temperature or humidity.
• Do not cover the ventilation holes with any items such as
newspapers, curtains etc.
• Do not immerse the unit in water. If you spill liquid over it, dry it
immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive materials.
• Do not tamper with the unit’s internal components. This
invalidates the warranty.
• Only use fresh batteries. Do not mix new and old batteries.
• Images shown in this manual may differ from the actual display.
• When disposing of this product, ensure it is collected separately
for special treatment and not as normal household waste.
• Placement of this product on certain types of wood may result
in damage to its finish for which Oregon Scientific will not be
responsible. Consult the furniture manufacturer’s care
instructions for information.
• The contents of this manual may not be reproduced without the
permission of the manufacturer.
• Do not dispose old batteries as unsorted municipal waste.
Collection of such waste separately for special treatment
is necessary.
• Please note that some units are equipped with a battery safety
strip. Remove the strip from the battery compartment before
first use.
NOTE
The technical specifications for this product and the
contents of the user manual are subject to change without notice.
NOTE
Features and accessories will not be available in all
countries. For more information, please contact your local retailer.
SPECIFICATIONS
MAIN UNIT
L x W x H
128 x 26 x 91 mm
(5.04 x 1.02 x 3.58 in)
Weight
158g (5.57 oz) without batteries
Temperature range
-5°C to 50°C
(23°F to 122°F)
Accuracy
0°C to 40°C: ± 1°C (± 2.0°F)
< 0°C and >40°C: ± 2°C (± 4.0°F)
Resolution
0.1°C (0.2°F)
Power
2 x UM-4 (AAA) 1.5 V batteries
3.6V adapter
REMOTE UNIT (THN132N)
L x W x H
96 x 50 x 22 mm
(3.78 x 1.97 x 0.87 in)
Weight
50 g (1.76 oz) without batteries
Transmission range
30 m (98 ft) unobstructed
Temperature range
-20 °C to 60 °C
(-4 °F to 140 °F)
Signal frequency
433 MHz
Power
1 x UM-3 (AA) 1.5 V batteries
ABOUT OREGON SCIENTIFIC
Visit our website
www.oregonscientific.com
to learn more about
Oregon Scientific products.
For any enquiry, please contact our Customer Services at
[email protected].
Oregon Scientific Global Distribution Limited reserves the right to
interpret and construe any contents, terms and provisions in this
user manual and to amend it, at its sole discretion, at any time
without prior notice. To the extent that there is any inconsistency
between the English version and any other language versions, the
English version shall prevail.
EU-DECLARATION OF CONFORMITy
Hereby, Oregon Scientific, declares that this PROJI Projection
Clock with Weather Forecast (model: BAR369PA) is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC. A copy of the signed and dated Declaration
of Conformity is available on request via our Oregon Scientific
Customer Service.
COUNTRIES RTTE APPROVED COMPLIED
All EU countries, Switzerland
CH
N
and Norway
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause
undesired operation.
WARNING
Changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help. This Class B digital apparatus complies with Canadian
ICES- 3(B)/NMB-3(B)
DECLARATION OF CONFORMITy
The following information is not to be used as contact for support
or sales. Please call our customer service number (listed on our
website at
www.oregonscientific.com), or on the warranty card for
this product) for all inquiries instead.
We
Name:
Oregon Scientific, Inc.
Address:
10778 SW Manhasset Drive.
Tualatin, Oregon 97062 USA
Telephone No.:
1-800-853-8883
declare that the product
Product No.:
BAR369PA
Product Name:
PROJI Projection Clock with Weather
Forecast
Manufacturer:
IDT Technology Limited
Address:
Block C, 9/F, Kaiser Estate,
Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon, Hong Kong
is in conformity with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: 1) This device may not
cause harmful interference. 2) This device must accept any
interference received, including interference that may cause
undesired operation.
INFORMATION FOR USERS
Pursuant to and in accordance with Article 14 of the
Directive 2012/19/EU of the European Parliament on
waste electrical and electronic equipment (WEEE), and
pursuant to and in accordance with Article 20 of the
Directive 2006/66/EC of the European Parliament on batteries and
accumulators and waste batteries.
The barred symbol of the rubbish bin shown on the equipment
indicates that, at the end of its useful life, the product must be
collected separately from other waste.
Please note that the batteries/rechargeable batteries must
be removed from the equipment before it is given as waste. To
remove the batteries/accumulators refer to the specifications in
the user manual. Therefore, any products that have reached the
end of their useful life must be given to waste disposal centers
specializing in separate collection of waste electrical and
electronic equipment, or given back to the dealer when purchasing
a new WEEE, pursuant to and in accordance with Article 14 as
implemented in the country.
The adequate separate collection for the subsequent start-up
of the equipment sent to be recycled, treated and disposal of in
an environmentally compatible way contributes to preventing
possible negative effects on the environment and health and
optimizes the recycling and reuse of components making up the
apparatus.Abusive disposal of the product by the user involves
application of the administrative sanctions according to the laws
in force.
PROJI Réveil projecteur Alarme
avec prévisions météo
Modèle :BAR369PA
Mode d’emploi
FR
INTRODUCTION
Merci d’avoir choisi le PROJI Réveil projecteur Alarme avec
prévisions météo d’Oregon Scientific™ (modèles: BAR369PA).
Cet appareil regroupe une mesure du temps précise, deux
alarmes, et un suivi des températures dans un outil unique que
vous pouvez utiliser dans le confort de votre maison. Conservez
ce mode d’emploi à disposition lors des premières utilisations de
ce produit. Il contient des instructions étape par étape, ainsi que
des spécifications techniques et autres avertissements que vous
vous devez de connaitre.
CONTENU DE L’EMBALLAGE
1
Unité principale
Adaptateur
secteur
Capteur sans fil
(THN132N)
2 piles AAA pour l’unité
principale
Pile AA pour le capteur sans fil
vUE D’ENSEMBLE
vUE DE DESSUS
1
2
3
4
5
6
1.
+ -
Appuyez ici pour augmenter les réglages, ou sélectionner
un des canaux (de 1 à 5) ou le réglage en boucle automatique.
Maintenez appuyé pour augmenter rapidement les valeurs en
mode réglage, ou rechercher les capteurs pour tous les canaux
en mode veille.
2.
SNOOZE | LIGHT
(veille/Lumière)
– Appuyez pour mettre
en veille l’alarme ou activer le projection. Maintenez appuyé
jusqu’à ce que vous entendiez un bip sonore pour activer le
projection pendant 5 minutes.
3.
- Appuyez pour alterner entre l’affichage de l’heure,
du calendrier ou de l’alarme 1 ou 2 pendant 5 secondes.
Maintenez appuyé pour entrer dans le mode de réglage.
4. – - Appuyez ici pour diminuer les réglages, ou maintenez
appuyé pour diminuer rapidement les valeurs en mode réglage.
5. Lentille de projection
6.
- Appuyez pour activer/désactiver les alarmes, maintenez
appuyé pour entrer dans le mode de réglage des alarmes.
vUE ARRIERE
1
2
3
4
5
6
1. Compartiment à piles.
2.
- Molette de mise au point de la projection.
3.
RESET
(
Réinitialisation
) – Appuyez ici pour réinitialiser
l’appareil.
4.
/
PROJECTION
- Appuyez ici pour inverser l’image
projetée de 180 degrés. Maintenez appuyé pour mettre la
projection en continue sur on/off.
5.
RCC
– Appuyez pour activer et rechercher le signal RCC.
Maintenez appuyé pour désactiver la recherche de signal.
6. Couvercle du compartiment à piles.
ECRAN LCD
1
2
3
4
5
1. Affichage de l’heure
2. Affichage des prévisions météo
3. Affichage de la température extérieure (canaux 1-5)
4. Affichage des jours de la semaine
5. Affichage de la température intérieure
Symbole
Description
Alarme 1 activée
Alarme 2 activée
Signal RCC reçu
Niveau des piles du capteur
d’extérieur faible
Niveau des piles de l’unité principale
faible
Réception du signal du capteur
La fonction de boucle automatique du
capteur d’extérieur est activée
Canaux du capteur d’extérieur
PROJECTION
2
1
1. Affichage de l’heure
2. Affichage des prévisions météo
CAPTEUR SANS FIL (THN132N)
1. Indicateur d’état LED
2. Trou pour la fixation murale
3. Compartiment à piles
4. Trou pour le
RESET
(Réinitialisation)
5. Sélecteur de
CHANNEL (Canal)
REMARQUE
Cet emballage comprend un capteur 3-canaux.
Si vous souhaitez utiliser un capteur avec jusqu’à 5 canaux,
vous pouvez acheter des capteurs supplémentaires en fonction
de vos préférences. Pour plus de détails concernant les capteurs
supplémentaires, veuillez visiter www.oregonscientific.com.
POUR COMMENCER
INSTALLATION DES PILES
1. Poussez doucement le couvercle du compartiment à piles vers
le bas pour le retirer de l’unité principale.
2. Installez les piles en respectant les indications de polarité (+/-).
REMARQUE
Remplacez les piles lorsque l’icone
s’affiche
ou lorsque la luminosité de l’affichage diminue.
ALIMENTATION SECTEUR
Branchez le câble de l’adaptateur secteur sur la prise d’alimentation
de l’appareil puis branchez l’adaptateur sur une prise de courant.
REMARQUE
Il est recommandé d’installer les piles en tant que
source d’alimentation de secours.
CAPTEUR SANS FIL
L’unité principale peut collecter des données jusqu’à 5 capteurs.
Pour régler le capteur:
1. Ouvrez le compartiment à pile.
2. Insérez les piles en respectant les indications de polarité (+/-).
3. Sélectionnez un canal et appuyez sur
RESET (REINITIALISER)
.
4. Refermez le compartiment à pile.
Placez le capteur dans les 30m (98ft) autour de l’unité principale en
utilisant le support table ou la fixation murale.
ASTUCE
Le positionnement idéal pour le capteur se trouve
en tout lieu à l’extérieur de la maison à une hauteur maximale de
1,5 m (5 pieds) et protégé de la lumière directe du soleil ou de
l’humidité pour une lecture précise.
1.5m(5ft)
REMARQUE
Utilisez des piles alcalines pour une durée
d’utilisation supérieure et des piles au lithium pour la consommation
lors de températures inférieures au gel.
TRANSMISSION DES DONNÉES DU CAPTEUR
Pour rechercher un capteur:
Maintenez appuyée la .
L’icone de réception du capteur dans la zone du capteur à distance
indique les états suivants :
Icone
Description
Recherche de capteur(s).
Capteur trouvé
Impossible de trouver un capteur
ASTUCE
La portée de transmission peut varier en fonction
de nombreux facteurs. Vous devrez peut-être essayer plusieurs
emplacements pour obtenir les meilleurs résultats.
HORLOGE
RÉCEPTION DE L’HORLOGE
L’horloge est désignée pour se synchroniser automatiquement
avec un signal d’horloge. Appuyez sur RCC pour activer et
rechercher le signal d’horloge.
L’unité principale est capable de recevoir des données d’horloge
RF suivant différents signaux
RCC
:
Numéro du
modèle
Région
Signal
BAR369PA
US
WWVB
Indicateur de réception du signal d’horloge:
Icones
Description
L’unité principale est à la
recherche d’un signal d’horloge
suffisement puissant.
(flash)
L’unite principale est à la
recherche d’un signal d’horloge.
Pas de signal d’horloge
Signal RCC reçu fort
Signal RCC reçu faible
REMARQUE
Il faut de 2 à 10 minutes pour recevoir le signal
d’horloge. Si le signal est faible, cela pourra prendre jusqu’à
24 heures pour recevoir un signal valide.
