background image

13

EN

NOTE ON COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operations.

Warning:   Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

FCC  :

NOTE:  This equipment has been tested and found to comply with
the limits for a Class  B digital device, pursuant to Part 15 of the FCC
Rules.  These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful  interference to radio communications.

However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

o

Reorient or relocate the receiving antenna.

o

Increase the separation between the equipment and receiver.

o

Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

o

Consult the dealer of an experienced radio/TV technician for
help.

Company Name: Oregon Scientific, Inc.

Address: 19861 SW 95th Place, Tualatin, Oregon 97062, USA

Telephone Number: 1-800-853-8883

Name and model number of the product: Weather Station
BAA182HG

CAUTION

— The content of this manual is subject to change without

further notice.

— Due to printing limitation, the displays shown in this

manual may differ from the actual display.

— The contents of this manual may not be reproduced without

the permission of the manufacturer.

CUSTOMER ASSISTANCE

Should you require assistance regarding this product and its

operation, please contact our customer care department at

800-853-8883 or via email at [email protected].

Summary of Contents for BAA182HG















Reviews: