6
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
To Replace Filter Dust Bag
WARNING: Unplug cord from electrical
outlet before servicing.
BAG REMOVAL:
fig. 11 Unzip outer bag completely.
fig. 12 Pull bag cardboard collar to release bag dock door from
connector. Bag dock door will hinge downward.
fig. 13 Gently pull bag cardboard collar upward out of the bag dock.
Saniseal
®
dust seal will close automatically.
BAG INSTALLATION:
fig. 14 Slide the cardboard collar completely onto bag dock door.
fig. 15 Firmly push bag dock door with both thumbs on indication point
until it snaps.
Bulb Replacement
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 16 Remove lamp housing by removing two (2) screws in the top of
the lamp housing. Pull burned out bulb from holder and replace
with new bulb. Replace lamp housing by replacing two screws
in the top of the lamp housing.
How to Replace a Worn Belt
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 17 Remove the replacement belt from the storage channel.
fig. 18 Remove the door by removing the hold down screw located on
side of power head.
fig. 19 Fold door away from the power head and lift it away.
fig. 20 Remove the belt from the motor drive shaft and brush roll pulley.
fig. 21 Loop the new belt over the brush roll pulley. Place the opposite
end of the belt on the motor drive shaft.
fig. 19 Replace the door by placing the bottom tab on door into slots
located inside power head and pressing the door closed.
fig. 18 Replace the hold down screw and tighten.
To Adjust or Replace Brush
WARNING: Unplug cord from electrical
outlet before servicing.
Your Oreck Vacuum comes with the brush roll set at the
NORMAL
position for most types of carpets. When using vacuum primarily on
Berber Carpets, adjust brush roll to the
SPECIAL setting.
fig. 22 Remove the baseplate by removing 5 screws. Then, remove the
belt and brush roll from the housing.
fig. 23 Rotate both end cards of the brush roll to show “SPECIAL” and
replace in the holding channels of the housing.
fig. 24 NOTE: The one marked “SPECIAL” has several ribs on top of
the end card.
fig. 25 The brush end card setting marked “NORMAL” has one rib.
When rotating bearings, make sure both end card assembly
settings are the same and face up when replacing the brush roll.
fig. 22 Reassemble the belt and the baseplate.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the filter bag
is to trap dirt, but at the same time it must be porous enough to allow air
to pass through. If the filter bag becomes clogged, no air can pass
through the cleaner and cleaning cannot take place, regardless of the
cleaner’s power.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently.
DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
Be sure the disposable paper filter dust bag is installed properly.
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK TYPE CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.
HEPA-Celoc
®
Hypo-Allergenic Filter System
The HEPA-Celoc outer bag of your vacuum cleaner is high filtration
medical material designed to filter the smallest of dust particles. It is
important the inside of the outer bag be cleaned. Vacuum the inside of
the outer bag or hand wash, turned inside out, with warm water, and air
dry. If desired, the HEPA-Celoc outer bag can be replaced for renewed
efficiency. The Celoc layered disposable inner dust bag must be
replaced once a month even if it
is not full. Change it more often if it is
used in extremely dirty areas.
Increase the cleaning power of your
vacuum by changing the bag often.
The Belt
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than ORECK belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
Motor Filter
The motor filter is used to filter tiny particles released by the motor
exhaust while in operation. The motor filter is not necessary for
operation but is helpful in removing contaminants from the air.
NOTE: Motor filter should be replaced every two months for best
performance.
Oreck Fresh Air
®
Cartridges
A fresh air cartridge adds a desired fragrance to the air while
vacuuming. It is placed behind the motor filter and uses heat and air
generated from the motor to spread the fragrance.
NOTE: Cartridge should be replaced every month when filter dust bag
is replaced or as desired.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
General Cleaner Care
fig. 10 At least once a month, check for and remove excessive lint,
string or hair from revolving brush. Patented cleaning grooves
on brush roll will allow easier cleaning.
Wipe the outside of the cleaner with a damp cloth. Also clean the
connector deflector assembly area, base of cleaner and fan housing
area. If there is dust in the outer bag, vacuum it or shake it out.
A little preventative maintenance will keep your cleaner looking new and
will ensure continued cleaning effectiveness.
