background image

 

MNL940-677-000  

 

 

 

REV- B   

 

 

 

3/20/2017 

 

WARRANTY CERTIFICATE

 

 

Behlman Electronics, Inc. warrants to the original purchaser, for a period of one (1) year from the 

shipment from Behlman, each item to be free from defects in material and workmanship. Behlman’s 

obligation and the Purchaser’s sole remedy for any breach or violation of this agreement is limited to 

adjustments, repair or replacements for parts which have been promptly reported by the Purchaser as 

having been in its opinion, defective and so found by Behlman upon inspection. All replacement parts will 

become the property of Behlman on an exchange basis. This warranty will not apply if such adjustment 

repair or parts replacement is required because accident, neglect, misuse, failure of environmental 

controls, transportation damage or causes other than normal use. 

 

If during the warranty period a defect should impair the performance of the unit, Behlman agrees, at its 

option, to repair or replace the unit or its defective components F.O.B. Behlman at 80 Cabot Court, 

Hauppauge NY 11788 or at another Behlman service facility at Behlman’s option. To obtain service under 

this warranty, the original Purchase shall notify Behlman at the above address or by telephone at 631-

435-0410 and provide information about the defect or impairment of performance. Behlman with then 

supply the Purchaser a Return Material Authorization (RMA) number. This number must be attached to 

the equipment sent back for warranty repair. Equipment must be shipped back to Behlman prepaid. No 

collect shipments will be accepted. 

 

Behlman shall be excused from supplying warranty service if the unit’s case has been opened  or if the 

unit has been subject to unauthorized repair. All service outside the scope of this warranty shall be paid 

for by the Purchaser at Behlman’s rates in effect at the time of this repair. Behlman will not perform any 

repairs outside of the warranty without written authorization by the Purchaser. If the repair is a warranty 

repair, Behlman will ship the unit back to the Purchaser, by a method determined solely by Behlman, 

prepaid. If the Purchaser requests, any other means of transportation it shall be at the Purchaser’s 

expense. 

 

The use of the equipment shall be under the Purchaser’s exclusive management and control. The 

Purchaser will be responsible for assuring the proper installation, use, management and supervision of 

the equipment. Behlman will not be liable for personal injury or property damage.  

 

The forgoing warranties are in lieu of all other warranties, expressed or implied including without limitation 

warranties of merchantability and fitness for purpose. 

 

In no event shall Behlman be liable for loss of profits, loss of use, or any indirect, consequential or 

incidental damages. Purchaser agrees that Behlman will not be liable for any damages caused by the 

Purchaser’s failure to fulfill any of the Purchaser’s responsibilities set forth herein. 

Summary of Contents for Behlman INV-1200 Series






















Reviews: