Oracle X7-8 Service Manual Download Page 47

Page: 47 / 308

Troubleshooting and Diagnostics

This section provides information about troubleshooting hardware component faults for the

Oracle Server X7-8. The following topics are covered.

■

“Detecting and Managing Server Faults” on page 47

■

“Troubleshooting Using Diagnostic Tools” on page 58

■

“Troubleshooting Using Status Indicators” on page 59

■

“Troubleshooting Server Subsystems” on page 81

■

“Attaching Devices to the Server” on page 89

■

“Getting Help” on page 94

For more information about server troubleshooting and diagnostics, refer to the

Oracle x86

Servers Diagnostics and Troubleshooting Guide for Servers With Oracle ILOM 4.0.x

http://

www.oracle.com/goto/x86admindiag/docs

Detecting and Managing Server Faults

When a server encounters a fault, the fault is recorded in a common fault database. The fault

is then reported by the server in one of several ways, depending on the type and severity of the

fault.

This section contains maintenance-related information and procedures that you can use to

troubleshoot and repair server hardware issues.

These topics explain how to use diagnostic tools to monitor server status and troubleshoot faults

in the server.

Description

Section Links

Troubleshooting overview information and

procedure

“Troubleshooting Server Hardware Faults” on page 48

Information about how to use the CMOD

Fault Remind Test Circuit

“Troubleshooting Using a CMOD Fault Remind Test Circuit” on page 55

Troubleshooting and Diagnostics

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands