manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 81

Troubleshooting Server Subsystems

Feedback Flash

The indicator flashes on and off during periods of activity, commensurate with the activity, but

the flashing does not exceed the 2 Hz fast blink rate (see, 

“Fast Blink Rate” on page 79

).

For example, this blink rate occurs during disk drive read and write activity and communication

port transmit and receive activity.

Data Blink Rate

For this blink rate, a normally on indicator repeatedly turns off twice during a one-second

interval (2 Hz—see also, 

“Fast Blink Rate” on page 79

) while data activity is taking place.

Sequential (Diagnostic) Blink Rate

This blink rate is a repeating sequence in which each indicator successively lights for 0.5 sec

to indicate that diagnostics are running. This blink rate is used only on systems or components

capable of running diagnostics.

Troubleshooting Server Subsystems

These sections describe the server subsystems:

■

“Processor Subsystem” on page 82

■

“Memory Subsystem” on page 83

■

“Power Subsystem” on page 83

Troubleshooting and Diagnostics

81

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands