Oracle X7-8 Service Manual Download Page 108

Page: 108 / 308

Prepare the Server for Cold Service (Oracle ILOM CLI)

Power down the server. In the Actions section of the Summary Information page,

click the Power State Turn Off button.

This action powers off the server to Standby power mode. For more power off options, see

“Powering Down the Server” on page 111

In the Actions section of the Summary Information page, click the Locator

Indicator Turn On button.

This action activates the Locate Button/LED indicator LED on the server front panel. For other

options, see

“Managing the Locate Button/LED” on page 120

Click OK.

Once at the service location, press the Locate Button/LED button to deactivate

the indicator.

For more information, see

“Control the Locate Button/LED Locally” on page 121

Set up an ESD-safe space at the service location.

Set up a space where you can set components. See

“Performing Electrostatic Discharge and

Static Prevention Measures” on page 98

Perform warm service removal and installation procedures on components.

See

“Servicing Components” on page 123

Prepare the Server for Cold Service (Oracle ILOM

CLI)

This procedure describes how to prepare the server for cold service when you remove, replace,

or install cold-serviceable components. A cold-service component must be serviced when

the server is completely powered off and AC cords have been removed from the back panel

AC power block. For more information about component serviceability, see

“Component

Serviceability Requirements” on page 26

108

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands