manualshive.com logo in svg

Oracle X7-2, Installation Manual, Page: 141 / 148

Share
Download
Oracle X7-2 Installation Manual Download Page 141

Preparation Checklists

Related Information

■

“Rack Space Requirements” on page 14

■

“Installing the Server Into a Rack” on page 39

Safety Checklist

Complete the following checklist to ensure that the safety requirements are met for the data

center where the server will be installed.

Safety Checklist Considerations

Yes

No

N/A Comment

Is there an emergency power shutoff?

 

 

 

 

Is there a fire protection system in the data center room?  

 

 

 

Is the computer room adequately equipped to extinguish

a fire?

 

 

 

 

Is antistatic flooring installed?

 

 

 

 

Is the floor below the raised floor free of obstacles and

blockage?

 

 

 

 

Related Information

■

“Electrical Requirements” on page 18

■

Oracle Server X7-2 Safety and Compliance Guide

■

Oracle Server X7-2L Safety and Compliance Guide

Auto Service Request Checklist

Complete the following checklist if you are planning to use Auto Service Request with the

server.

Auto Service Request Considerations

Yes

No

N/A Comment

Do you have a My Oracle Support Online Account to

register Auto Service Request?

 

 

 

 

Do you have your My Oracle Support Customer

Support Identifier (CSI) number?

 

 

 

 

Site Planning Checklists

141

Summary of Contents for X7-2





















































































































































Reviews:

No comments