Oracle X7-2 Installation Manual Download

Page: 18 / 148

Electrical Requirements

Note -

The combination of inlet and exhaust restrictions, such as cabinet doors and the

distance of the server from the doors, can affect the cooling performance of the server.

You must evaluate these restrictions. Server placement is particularly important for high-

temperature environments.

■

Manage cables to minimize interference with the server exhaust vent.

Electrical Requirements

The servers use AC power. The following table contains the power supply specifications for the

servers.

Note -

The power dissipation numbers listed in the following table are the maximum rated

power numbers for the power supply used in the server. The numbers are not a rating of the

actual power consumption of the server. For up-to-date information about power consumption,

go to the Oracle Power Calculators web site:

http://www.oracle.com/us/products/servers-

storage/sun-power-calculators/index.html

, and click the Oracle Server X7-2 or Oracle

Server X7-2L link.

Parameter

Specification

Voltage (nominal)

100-240 VAC

Input current (maximum)

100-127 VAC 7.2 A and 200-240 VAC 3.4 A

Frequency (nominal)

50/60 Hz (47 to 63 Hz range)

Maximum power consumption

2400 W

Maximum heat output

11600 BTU/Hr

The servers can operate effectively over a range of voltages and frequencies.

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands