Oracle X7-2 Installation Manual Download Page 14

Page: 14 / 148

Receiving and Unpacking Requirements

Dimension

Server Specification

Measurement

Weight

Fully populated server

40 lbs (18.1 kg)

Oracle Server X7-2L

Dimension

Server Specification

Measurements

Width

Server chassis

48.2 cm ( 18.9 inches)

Depth

Maximum overall

75.9 cm (29.9 inches)

Height

2-rack unit (2U) nominal

8.69 cm (3.42 inches)

Weight

Fully populated server

64 lbs (29.03 kg)

Receiving and Unpacking Requirements

When the server is unloaded at your site:

■

Leave the server in its shipping carton until it arrives at its installation location.

■

Use a separate area to remove the packaging material to reduce particle contamination

before the server is taken to the data center.

■

Ensure that there is enough clearance and clear pathways to move the server from the

unpacking area to the installation location.

■

Ensure the entire access route to the installation site is free of raised-pattern flooring that

causes vibration.

Rack Space Requirements

The Oracle Server X7-2 is a 1 rack unit (1U) server. Oracle Server X7-2L is a 2U server. For

physical dimensions, see

“Server Physical Specifications” on page 13

You can install the server into a four-post rack cabinet that conforms to ANSI/EIA 310-D-1992

or IEC 60297 standards, such as Oracle Rack Cabinet 1242 or Sun Rack II 1242. See

“Rack

Compatibility” on page 41

The minimum ceiling height for the cabinet is 230 cm (90 inches), measured from the true

floor or raised floor, whichever is higher. An additional 91.4 cm (36 inches) of ceiling height is

required for top clearance. The space above the cabinet and its surroundings must not restrict

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands