Oracle Sun Server X4-4 Installation Manual Download

Page: 81 / 148

Configuring RAID Using Oracle System Assistant

Configuring RAID Using Oracle System Assistant

Use Oracle System Assistant to configure RAID on the server. If your server does not have

Oracle System Assistant, you can use the BIOS Utilities to configure RAID.

See the following procedures:

■

“Configure RAID With a Sun Storage 6 Gb SAS PCIe Internal HBA” on page 81

■

“Configure RAID With a Sun Storage 6 Gb SAS PCIe RAID Internal HBA” on page 86

Configure RAID With a Sun Storage 6 Gb SAS

PCIe Internal HBA

Use Oracle System Assistant to prepare a server hard drive for an OS installation by creating a

bootable RAID 0 volume.

Before You Begin

You should have already selected a BIOS boot mode (UEFI or Legacy) from the BIOS Setup

Utility.

Note -

The BIOS boot mode used for the RAID configuration must match the mode that you

will use when you install the operating system; otherwise, the RAID configuration will not be

visible or usable.

Not all supported operating systems support UEFI mode. For a list of operating systems that

support UEFI mode, see

“UEFI BIOS” on page 24

For instructions for switching the BIOS boot mode from UEFI to Legacy BIOS, or Legacy

BIOS to UEFI, refer to

Oracle X4 Series Servers Administration Guide (

http://www.oracle.

com/goto/x86AdminDiag/docs

)

Launch Oracle System Assistant.

See

“Setting Up Software and Firmware Using Oracle System Assistant” on page 71

Configure Server Drives for OS Installation

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands