Oracle Sun Server X4-4 Installation Manual Download

Page: 86 / 148

Configure RAID With a Sun Storage 6 Gb SAS PCIe RAID Internal HBA

The RAID Configuration screen appears and lists the RAID volume as the current boot device.

10.

If you want to delete a volume, select it and click the Delete Volume button.

This completes the RAID configuration task.

11.

Do one of the following:

■

To select any other Oracle System Assistant task,

click the corresponding button in the

left panel menu. For example, after configuring RAID, you might want to select the Install

OS task and perform an operating system installation.

■

To return to the Oracle System Assistant System Overview screen,

click System

Information in the left menu panel.

■

To quit Oracle System Assistant,

click Exit.

Next Steps

■

“Set Up an Operating System and Drivers” on page 104

Configure RAID With a Sun Storage 6 Gb SAS

PCIe RAID Internal HBA

For systems with the Sun Storage 6 Gb SAS PCIe RAID Internal HBA, if you are not using

a preinstalled OS from Oracle you

must

create a bootable volume on a drive before installing

an OS. The system does not recognize a drive unless it has a volume on it created by the Sun

Storage 6 Gb SAS PCIe RAID Internal HBA.

If there is more than a single volume on the drive that you intend to use as the boot drive, the

volume that the OS will be installed on should be set as the boot device.

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands