Oracle Sun Server X4-4 Installation Manual Download

Page: 74 / 148

Launch Oracle System Assistant Locally

Refer to the

Oracle X4 Series Servers Administration Guide (

http://www.oracle.com/goto/

x86AdminDiag/docs

)

or the embedded help on Oracle System Assistant for more information

about using Oracle System Assistant.

Step

Task

Oracle System Assistant Screen

Set up Oracle System Assistant network

connection.

Network Configuration

Get latest software and firmware updates.

Get Updates

Update Oracle ILOM, BIOS, disk expander, or

HBA firmware, if needed.

Update Firmware

Configure Oracle ILOM.

Configure Hardware > Service Processor

Configuration

Configure RAID.

Note -

not

use this option on a disk with a

preinstalled OS.

Configure Hardware > RAID Configuration

Additional details for performing this task are

listed in

“Configuring RAID Using Oracle

System Assistant” on page 81

Install an operating system using the Oracle

System Assistant Install OS wizard. Supported

operating systems include Oracle Solaris, Linux,

Windows, or Oracle VM software.

Note -

not

use this option if your system

came with a preinstalled OS.

Install OS

Next Steps

■

“Configure Server Drives for OS Installation” on page 79

Launch Oracle System Assistant Locally

Before you begin to launch Oracle System Assistant locally, you must be physically present

with the Sun Server X4-4 and have access to the following:

■

VGA monitor

■

USB keyboard

■

USB mouse

Choose a method to launch Oracle System Assistant locally on a server module. as described in

the following sections:

Ensure that the server is in standby power mode.

Verify that the Power/OK indicator blinks slowly. See:

“Front Panel Features” on page 15

Connect locally to the server.

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands