Oracle Sun Server X4-4 Installation Manual Download

Page: 15 / 148

Server Features and Components

This section describes Oracle's Sun Server X4-4 hardware. It includes topics shown in the

following table:

Description

Links

Locate status indicators, connectors, and storage drives

on the server front and back panels.

■

“Front Panel Features” on page 15

■

“Back Panel Features” on page 16

Review server features and components.

“Server Supported Components” on page 17

Review server management software.

“Managing Your Server” on page 19

Front Panel Features

The following figure shows the Sun Server X4-4 front panel and describes its components.

Server Features and Components

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands