manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 159

Servicing the Drive Backplane

This board provides connectors for the drive signal cables. This board also serves as the

interconnect for the front I/O board, the Power and Locate buttons, and server or component

status LEDs.

These topics describe how to service the drive backplane.

■

“Remove the Drive Backplane” on page 159

■

“Install the Drive Backplane” on page 160

■

“Verify the Drive Backplane” on page 163

Remove the Drive Backplane

This is a cold-service procedure that must be performed by qualified service personnel. Power

down the server completely before performing this procedure.

Caution - 

This procedure requires that you handle components that are sensitive to ESD which

can cause server components to fail.

1.

Prepare for servicing.

See 

“Preparing for Service” on page 45

.

2.

Remove all drives and fillers.

See 

“Remove a Drive” on page 65

.

Note - 

Note the positions of the drives so you can return them to the correct slots.

3.

Remove one or more memory risers to have easier access to components in the

drive area.

See 

“Remove a Memory Riser” on page 98

.

4.

Remove the System Remind button assembly (air divider) by lifting it up and

away from the power supplies.

Servicing the Drive Backplane

159

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands