Oracle SG-SAS6-INT-Z Installation Manual Download Page 52

Page: 52 / 80

To Prepare to Install the Oracle Solaris OS

■

“To Prepare to Install the Oracle Solaris OS” on page 52

■

“To Install the Oracle Solaris OS:” on page 52

To Prepare to Install the Oracle Solaris OS

Ensure that you have a bootable drive upon which to install the Oracle Solaris

OS, as described in this chapter.

To Install the Oracle Solaris OS:

Obtain the Oracle Solaris 10 01/13 OS, at minimum, from the download site:

http://www.oracle.com/technetwork/server-storage/solaris10/overview/index.html

Perform a normal installation, as described in the Oracle Solaris 10 installation

documentation.

Apply any patches that are specifically required for the system.

You can obtain these Oracle Solaris patches at:

http://support.oracle.com

Reboot the system.

reboot

The system can now see, and boot from, the RAID volume on which you installed the Oracle

Solaris OS.

Next Steps

Continue with the HBA installation, as described in

“To Complete the Installation” on page 20

Sun Storage 6 Gb SAS PCIe HBA, Internal Installation Guide For HBA Models SGX-SAS6-INT-Z and SG-SAS6-INT-Z

• May 2017

Summary of Contents for SG-SAS6-INT-Z

















































































Search results

Summary of Contents for SG-SAS6-INT-Z

Reviews:

Related manuals for SG-SAS6-INT-Z

Brands by name

Popular brands

Oracle SG-SAS6-INT-Z, Installation Manual

Search results

Summary of Contents for SG-SAS6-INT-Z

Reviews:

Related manuals for SG-SAS6-INT-Z

Brands by name

Popular brands