manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual

The Oracle Netra SPARC S7-2 comes packed with cutting-edge features for optimal performance. To ensure seamless installation, simply download the user manual for free from manualshive.com, and get step-by-step instructions for easy setup. Find everything you need in the comprehensive installation manual, available for hassle-free download.

Share
Download
background image

Remove an NVMe Drive

See 

“Remove an NVMe Drive” on page 99

.

Related Information

■

“Remove an NVMe Drive” on page 99

■

“Verify Removal of an NVMe Drive” on page 100

■

“Install an NVMe Drive” on page 100

Remove an NVMe Drive

After you unmount the NVMe drive, the steps to physically remove the dirve are the same

as the steps to remove a SAS storage dirve. For detailed instructions, see 

“Remove a SAS

Drive” on page 89

.

1.

Unmount the drive depending on the OS.

See 

“Unmount an NVMe Drive” on page 98

.

2.

Follow safety and ESD precautions.

See 

“Prevent ESD Damage” on page 55

.

3.

Identify the physical location of the NVMe drive that you want to remove.

For drive locations, see 

“Component Locations (Storage, Power, NVMe, and Fan

Modules)” on page 14

.

4.

Tilt and pivot the air filter away from the server.

See 

“Remove the Filter” on page 79

.

5.

Verify that the OK to Remove LED on the NVMe drive is lit.

6.

Push the latch release button to open the drive latch.

7.

Grasp the latch, and pull the drive out of the drive slot.

8.

Consider your next step.

■

If you are replacing the drive, verify the removal.

See 

“Verify Removal of an NVMe Drive” on page 100

.

■

If you are not replacing the drive, install a filler in the empty drive slot to

maintain proper airflow, then perform administrative tasks to configure the

server to operate without the drive.

Servicing NVMe Storage Drives

99

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments

Related manuals for Netra SPARC S7-2

Canon ColorPASS-Z5000 Getting Started preview
ColorPASS-Z5000
Brand: Canon Pages: 130
Omneon MediaDeck Installation Manual preview
MediaDeck
Brand: Omneon Pages: 2
LaCie 5BIG NAS PRO Quick Install Manual preview
5BIG NAS PRO
Brand: LaCie Pages: 22
Cobalt Digital Inc Cobalt Qube 2 User Manual preview
Cobalt Qube 2
Brand: Cobalt Digital Inc Pages: 218
IBM 7944E2U User Manual preview
7944E2U
Brand: IBM Pages: 21
HPE ProLiant ML110 Gen 10 Product End-Of-Life Disassembly Instructions preview
ProLiant ML110 Gen 10
Brand: HPE Pages: 5
QNAP TS 73A Series User Manual preview
TS 73A Series
Brand: QNAP Pages: 68
Fujitsu B23Q8WD-G-01-J Hardware Manual preview
B23Q8WD-G-01-J
Brand: Fujitsu Pages: 26
Fujitsu FUTRO S450 Operating Manual preview
FUTRO S450
Brand: Fujitsu Pages: 56
Fujitsu FD-1000ST User Manual preview
FD-1000ST
Brand: Fujitsu Pages: 36
Fujitsu FUTRO S550 Operating Manual preview
FUTRO S550
Brand: Fujitsu Pages: 61
Fujitsu BS2000 Operating Manual preview
BS2000
Brand: Fujitsu Pages: 30
Fujitsu ETERNUS DX Disk Configuration Manual preview
ETERNUS DX Disk
Brand: Fujitsu Pages: 85
Fujitsu BS2000/OSD Operation Manual preview
BS2000/OSD
Brand: Fujitsu Pages: 111
Fujitsu BX630 - PRIMERGY - S2 Dual Options Manual preview
BX630 - PRIMERGY - S2 Dual
Brand: Fujitsu Pages: 64
Fujitsu ESPRIMO A525-L Operating Manual preview
ESPRIMO A525-L
Brand: Fujitsu Pages: 68
Fujitsu CELVIN NAS QE707 Operating Manual preview
CELVIN NAS QE707
Brand: Fujitsu Pages: 95
Fujitsu BX630 - PRIMERGY - S2 Dual Operating Manual preview
BX630 - PRIMERGY - S2 Dual
Brand: Fujitsu Pages: 90

Brands by name

Popular brands

Load more brands