manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual

The Oracle Netra SPARC S7-2 comes packed with cutting-edge features for optimal performance. To ensure seamless installation, simply download the user manual for free from manualshive.com, and get step-by-step instructions for easy setup. Find everything you need in the comprehensive installation manual, available for hassle-free download.

Share
Download
background image

Install the Fan Tray

See 

“Install the Fan Tray” on page 244

.

Related Information

■

“Rotate the Drive Cage to the Service Position” on page 71

■

“Install the Fan Tray” on page 244

Install the Fan Tray

Perform this task when you have previously removed the fan tray.

1.

If you previously removed the PSU and air ducts or raised the drive cage,

complete these prerequisites, as necessary, in this order.

See:

■

“Install the Air Duct” on page 236

■

“Install the PSU Duct” on page 240

■

“Secure the Drive Cage” on page 241

2.

Move any loose cables so that they are against the server walls.

Caution - 

The fan tray goes inside the latch line of the cable pass through. Take care when

installing the fan tray so that the cable pass through is not damaged or unseated.

3.

Install the fan cage bracket, being careful to avoid damage to any mother

board components that are near the end of the bracket that gets secured to the

motherboard.

Caution - 

The fan tray sits on top of the cable pass through. The cable pass through needs to be

properly seated when installing the fan tray. If not, damage may occur to the latch.

4.

Align the fan tray to where it installs into the server.

Two arrows on the top of power supply bay show where the fan tray aligns. Holes in the base of

the tray need to match up with fan connectors. If necessary, rotate the tray 180 degrees to align.

5.

Slowly lower the fan tray into the server.

Verify that the fan tray is properly seated, and the top surfaces of the fan tray are flush with the

server.

244

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments

Related manuals for Netra SPARC S7-2

ABLELink ABLELink SE5002 Series Quick Start Manual preview
ABLELink SE5002 Series
Brand: ABLELink Pages: 4
Blackberry Enterprise Server Upgrade Manual preview
Enterprise Server
Brand: Blackberry Pages: 88
LaCie 301300U - Ethernet Disk NAS Server User Manual preview
301300U - Ethernet Disk NAS Server
Brand: LaCie Pages: 62
SafeNet ProtectServer External 2 Installation Manual preview
ProtectServer External 2
Brand: SafeNet Pages: 22
Supermicro A+ AS-2124US-TNRP User Manual preview
A+ AS-2124US-TNRP
Brand: Supermicro Pages: 130
t.a.c. TAC Xenta 511 Handbook preview
TAC Xenta 511
Brand: t.a.c. Pages: 36
Obvius, LLC AcquiLite A7810-0 Installation And Operation Manual preview
AcquiLite A7810-0
Brand: Obvius, LLC Pages: 29
Epson C823781 Software Installation Manual preview
C823781
Brand: Epson Pages: 28
Epson EpsonNet 802.11b Product Support Bulletin preview
EpsonNet 802.11b
Brand: Epson Pages: 30
Epson Stylus C80WN - Ink Jet Printer Hardware preview
Stylus C80WN - Ink Jet Printer
Brand: Epson Pages: 1
Epson C823781 Administrator'S Manual preview
C823781
Brand: Epson Pages: 258
Epson C82378 Administrator'S Manual preview
C82378
Brand: Epson Pages: 280
Fujitsu PRIMERGY RX300 S6 Options Manual preview
PRIMERGY RX300 S6
Brand: Fujitsu Pages: 132
Fujitsu PRIMERGY RX300 S5 Operating Manual preview
PRIMERGY RX300 S5
Brand: Fujitsu Pages: 112
Fujitsu PRIMERGY RX2540 M4 Operating Manual preview
PRIMERGY RX2540 M4
Brand: Fujitsu Pages: 86
Fujitsu PRIMERGY RX2540 M6 Operating Manual preview
PRIMERGY RX2540 M6
Brand: Fujitsu Pages: 121
Fujitsu PRIMERGY RX4770 M6 Upgrade And Maintenance Manual preview
PRIMERGY RX4770 M6
Brand: Fujitsu Pages: 468
Fujitsu PRIMERGY RX2540 M1 Operating Manual preview
PRIMERGY RX2540 M1
Brand: Fujitsu Pages: 92

Brands by name

Popular brands

Load more brands