Oracle Netra SPARC S7-2 Service Manual Download

Page: 209 / 258

Install NVMe Cables

Remove the air duct.

See

“Remove the Air Duct” on page 75

Remove the NVMe cables from the server.

Carefully remove the NVMe cable bundle from the server. Be careful not to snag the cables on

the server components.

Related Information

■

Oracle 1.6TB NVMe SSD Documentation Library

■

“Component Locations (Storage, Power, NVMe, and Fan Modules)” on page 14

■

“Component Locations (Motherboard, Memory, and PCIe Cards)” on page 16

■

“Preparing for Service” on page 43

■

“Install NVMe Cables” on page 209

■

“Returning a Server to Operation” on page 235

Install NVMe Cables

Replacing the cable assembly is a cold-service procedure that must be performed by qualified

service personnel. The server must be completely powered down before performing this

procedure.

Install the NVMe cables between the front storage drive backplane and the

motherboard.

Caution -

Be careful not to break any wires or base connectors when bending and folding a

cable.

If installing a new cable, bend it near the white tape banding, at the base

connector, to conform with the cable routing.

Tip -

Using the handle of a small screwdriver as a form helps bend the cables while protecting

the wires going into the base connectors. If necessary, the white tape banding can be split to

maintain the integrity of the cable.

Plug each cable into its port connector until you hear an audible click.

Servicing the Cables

209

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands