Oracle Netra SPARC S7-2 Service Manual Download

Page: 202 / 258

Install the Drive Power Cable

■

“Returning a Server to Operation” on page 235

Install the Drive Power Cable

Installing a cable is a cold-service operation. You must power off the server before installing the

cable.

Connect the cable to the motherboard.

Route the cable into the cable clamp and against the server wall.

If you removed the fan modules and tray, complete these prerequisites in this

order.

See:

■

“Install the Fan Tray” on page 244

■

“Install a Fan Module” on page 155

Install all fan modules.

202

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands