manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 177 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 177

Verify a PCIe Card

6.

Swing the retainer to its fully closed position.

If there is resistance, check the alignment of the PCIe card bracket and try again.

Caution - 

Do not force the card into the slot. Damage to the card or the server might occur.

7.

Repeat from 

Step 4

 through 

Step 6

 for additional PCIe cards that you are

installing.

8.

If you installed a PCIe card as part of another component's removal or

installation procedure, return to that procedure.

See 

“Component Service Task Reference” on page 47

.

9.

Complete these postrequisites in this order to finish the installation procedure.

See:

■

“Returning a Server to Operation” on page 235

■

“Verify a PCIe Card” on page 177

Related Information

■

“Remove a PCIe Card” on page 174

■

“Verify a PCIe Card” on page 177

■

“PCIe Card Configurations” on page 170

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Verify a PCIe Card

After you install a PCIe card, you can verify its functionality.

1.

Access Oracle ILOM.

See 

“Log In to Oracle ILOM (Service)” on page 26

.

2.

Reset the PCIe card.

-> 

set /SYS/MB/PCIE

y

 clear_fault_action=true

Are you sure you want to clear /SYS/MB/PCIE1 (y/n)? 

y

Set 'clear_fault_action' to 'true'

Servicing PCIe Cards

177

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments