Oracle Exadata Storage Server X7-2 EF Installation Manual Download Page 33

Page: 33 / 90

Installing the Storage Server Into a Rack

This section describes how to install the storage server into Sun Rack II cabinet using the slide-

rail assembly in the Rackmount Kit. Figures for the rackmounting procedures depict the EF

server. The procedures are the same for the HC server. Perform these procedures if you are

inserting additional storage servers into your Exadata Database Machine configuration.

For instructions on how to install the storage server into the Oracle Rack Cabinet 1242,

refer to the

Oracle Rack Cabinet 1242 User's Guide

http://www.oracle.com/goto/

oraclerack1242/docs

Note -

In this guide, the term "rack" means either an open rack or a closed cabinet.

■

“Installation Prerequisites” on page 33

■

“Safety Precautions” on page 34

■

“ESD Precautions” on page 35

■

“Rack Compatibility” on page 36

■

“Rackmount Kit Contents” on page 37

■

“Rackmounting the Server” on page 38

Related Information

■

“Installation Procedure” on page 11

■

“Preparing for Server Installation” on page 13

Installation Prerequisites

Before you start the rackmount procedures, ensure that your site meets the required electrical

and environmental requirements. See

“Preparing for Server Installation” on page 13

Installing the Storage Server Into a Rack

Summary of Contents for Exadata Storage Server X7-2 EF



























































































Search results

Summary of Contents for Exadata Storage Server X7-2 EF

Reviews:

Related manuals for Exadata Storage Server X7-2 EF

Brands by name

Popular brands

Oracle Exadata Storage Server X7-2 EF, Installation Manual

Search results

Summary of Contents for Exadata Storage Server X7-2 EF

Reviews:

Related manuals for Exadata Storage Server X7-2 EF

Brands by name

Popular brands