Oracle 1242 Page 36 User Manual Download

Page: 36 / 84

Stabilize the Rack (Leveling Feet)

Related Information

■

“Installation Task Overview” on page 31

■

“Rack Packaging” on page 32

■

“Tools Required” on page 33

■

“Stabilize the Rack (Leveling Feet)” on page 36

Stabilize the Rack (Leveling Feet)

After you move the rack to the installation site, stabilize the rack using the leveling feet to

ensure it does not move or tip over when you install equipment.

Lower the four leveling feet to share the load with the casters. This increases the footprint of the

rack which improves stability and helps prevent rack movement.

Stabilize the rack by lowering the four leveling feet to the floor, using a 6-mm hex

wrench or your fingers.

Lock the leveling feet using an 18-mm open wrench.

Caution -

When moving the rack to a new location, including repacking, verify that the leveling

feet are up before moving the rack.

Related Information

■

“Installation Task Overview” on page 31

■

“Rack Packaging” on page 32

■

“Tools Required” on page 33

Oracle Rack Cabinet 1242 User's Guide • July 2018

Summary of Contents for 1242





















































































Search results

Summary of Contents for 1242

Reviews:

Related manuals for 1242

Brands by name

Popular brands

Oracle 1242, User Manual

Search results

Summary of Contents for 1242

Reviews:

Related manuals for 1242

Brands by name

Popular brands