Opus aeroPOUCH 4 User Manual Download Page 10

Page: 10 / 11

OPUS aeroPOUCH 4 Instrukcja

obsługi / User guide

•

Press the Start / Pause button to

start making the air bags.

•

You can stop the process at any time with the Start / Pause button and tear off the

produced cushions at the perforated

line. If it is necessary to replace the foil, remove

the entire foil from the device.

•

Air pressure setting can be adjusted to suit the size of the air bags and packaging

requirements. If the air bag is too full, it may get damaged.

Attention!

When using foil

bags up to 200 mm high, use the lower ranges on the dial.

•

Speed adjustment for the

foil passing through the sealing rollers, depends on the size

and air needed to fill the bags. The efficiency of the device is fully adjustably to suit

your requirements.

•

Temperature control can be set in three levels, Low

Middle

High, depending on the

size of the foil bags used.

•

ATTENTION:

Before turning off the power, press the stop/pause button, then remove

the bags from the sealing rollers and tear off the bags at the perforated lines at the air

nozzle. Then turn off the power.

•

Note:

The device needs approximately 3

5 minutes to warm up from cold start. We

suggest putting the foil on immediately after turning on the power.

•

Standby function:

when the device is not used for 30 minutes, equipment will go into

a standby mode and the READY indicator light will start blinking. To restart the heating

process, press the Start / Pause button and wait until the appliance heats up and the

READY light comes on.

CUTTER REPLACEMENT

•

Pulling out the air nozzle tube assembly.

•

Insert a new set (knife with air nozzle) until you hear a click, which confirms that the

element has been installed correctly.

•

WARNING:

Sharp blade, take care not to cut yourself when replacing the blade

MAINTENANCE

•

Unplug the power cable during maintenance.

•

Clean the hot sealing rollers regularly.

•

Ensure there is no foil stuck or jammed on or in the roller mechanism and there is on

dirty or dust around the air inlet vent.

•

Check the air nozzle and the cutting blade regularly.

•

Renew the cutter blade regularly.

•

WIAIIR-1200

Air Cushion Machine

Instruction manual

A B C

D E F

A Cold roller

B Air nozzle
C Hot roller

E Air volume adj.

F Feeding speed adj.
G Feeding roller

I Start/Pause button

J Power switch

K Temperature select switch

D Tension roller

H Electrical Cable

4. Cutter replacement

Air nozzle cutter blade assembly replacement steps
4.1.Pulling out the air nozzle. Refer fig.6
4.2 Insert the new blade assembly of the air nozzle, and hear the click sound, which means

that it has been installed in place. Refer fig.7

4.3 Renew the new cutter blade assembly be care of sharp blade may cut you fingers.

5. Machine Maintenance

5.1 Unplug the power cord during maintenance.
5.2 Clean hot seals and rollers regularly.
5.3 Ensure there is no jammed film and dirt at the air nozzle or cutter blade.
5.4 Check the blade and rollers regularly.
5.5 Replace the cutter blade when blade is not sharp.

6. Specification

Sealing speed

12m/min±10%(adjustable)

Air density control

Adjustable

(2001400mm

inadifferent setting

and operation range)
200x80mm, 200x100mm, 200x130mm

Film roll size

200x150mm, 200x200mm

400x250mm, 400x290mm

Max. Film roll length

(W: Film width) (L: Film length)

200mm ::;;sooM

400mm ::;;500M

Power voltage
Power rate

Machine size
Machine weight

220-240VAC 50Hz

250W

300x260x260(mm)

3.5kg

1. Caution

Please read carefully before use.

1.1 Remove the machine from the package box carefully.
1.2 Put the machine in the clean and flat workbench,

close to edge as well.

2. Installation Steps

2.1 Connect the correct electrical power.
2.2 Installation of film roll.

2.2.1 The bubble film should be cut with a scissorsin the lower right corner before

loading the film, Refer fig.1.

2.2.2 Put the roll film on the feeding roller properly. There is a groove inside the roll film

header should align and feed into feeding roller's protrusion part. Refer fig.2.

2.2.3  The roll feeding direction to pass through to the tension column,  Refer fig.3.
2.2.4  Threading roll film pass through the air nozzle. Refer fig.4.
2.2.5  Pulling the roll film to close enough and touch just right between the hot sealing

wheels to ensure when push start button the machine can pull out film till out of
the roller wheels, and start making air cushion smoothly. Refer fig.5.

Approximately

3cm (1-1/2") cut off corner.

Air Volume adj. knob. Feeding speed adj. knob. Start/ Pause button

Power on indicate LED Warm up ready LED

2.3 Operations

TTT

[DJ

Three-stage temperature seeting switch

2.3.1 Turn on the power switch. (Note: Please confirm the function of each part of the

operation panel before operating the machine)

2.3.2 After power light is on and the ready light start to blinking, machine hot roller

start to warm up till ready light stop blinking mean machine is ready to use.

2.3.3 Press the start/pause button and the machine starts making bubble cushions.

2.3.4 When Press the Start/Pause button machine will start to making air cushions,

user can stop at any position and tear off the cushions via perforation line by the

end out let of machine at the length for requirement. (as for replace new roll film,
should eject all film out of roller completely.)

2.3.5 Air density setting:

Various cushion sizes are available to meet different packaging requirements,

you can set the air density volume to meet your requirements, to much air volume
or over inflation will result in defect.
Notes: When using the bubble bag with the height of 200mm, the air volume

should not rotate too much, and try to use it within the adjustment range of less

than

(as shown in the figure).

2.3.6 Different material or thickness types of air cushion bags can be selected by a

three-stage temperature switch.

2.3.6 If want to poweroff, please make sure machine is stop, tear off the film ahead the

air nozzle, and turn off the power switch.

Notes: the machine needs to warm up for about 3~5 minutes each time from cold state.

It is recommended to install the film roll right after the machine power on.

2.4 Energy saving function

Machines without any operation after 30 minutes, will lower the power output and enter
a energy saving state, and READY light blinking, if want to wake up machine, need to

press Start/Pause button again into the warm up process till the READY light is normally
on, may continue to produce air cushion bag.

3. Electric Safety

3.1 Place the machine close to power socket.
3.2 Make sure the voltage meets machine's electricity requirements.
3.3 Any extension cord used should meet the power rating of the machine.
3.4 Do not operate if the power cord is damaged.
3.5 Repair and service should be done by a qualified service technician.

OPUS aeroPOUCH 4 Instrukcja

obsługi / User guide