background image

 

 

1 | 

S t r e a m L i n e   2 0 1 7  

 

OptoLum StreamLine Linear Light Strips 

   StreamLine HO, LO 
 

SAVE THESE INSTRUCTIONS  
Important Safety Instructions 

a)

 

Read all instructions. 

b)

 

Do not conceal or extend exposed conductors through a building wall. 

c)

 

Do not install this luminaire in wet or damp locations. 

d)

 

To reduce the risk of fire and burns, do not install this lighting system where the exposed bare 
conductors can be shorted or contact any conductive material. 

e)

 

To reduce the risk of fire and overheating, make sure all connections are tight. 

f)

 

Do  not  install  any  luminaire  closer  than  6  inches  (150mm)  from  any  curtain,  or  similar 
combustible materials. 

g)

 

Turn off electrical power before modifying the lighting system in any way

 

GETTING STARTED 

OptoLum StreamLine offers indoor cove lighting, display case lighting, and wall washing in a compact, 
linear form.  This guide contains important information on planning, installing, and operating your new 
StreamLine Luminaire. For your protection, read it carefully and save it for future reference. 
 

INCLUDED IN THIS BOX 

 

1 - StreamLine Luminaire with mating power connector to attach to power supply. 

 

1 - Set of mounting clips, or foam tape, or magnetic strips.  Mounting clips are pre-drilled to 
accommodate  a  #4  Pan  Head  Screw  (Not  Included).    Foam  tape  and  magnetic  strips will  be 
pre-applied to StreamLine Luminaire at manufacturer specified locations. 

 

1 - Installation Guide 

 

ADDITIONAL ITEMS NEEDED 

 

1  –  UL  Listed,  Class  2,  24VDC  power  supply  with  mating  secondary  power  connector  that 
matches to StreamLine power connector, and wire leads for connection to primary 120VAC. 

 

#4 Pan Head Mounting Screws (1 per Mounting Clip) 

 

Screwdriver 

 

Drill 

 

Level or Chalk Line  

 

SCOPE OF THIS USER GUIDE 

The goal of this user guide is to explain, in an easily understandable language, the necessary steps to 
install StreamLine Luminaires and assure peak performance.  Its intended use is for reference only, by 
persons  who  are  fully  qualified.    This  document  should  never  be  considered  a  substitute  for  any 
provision of a regulation or state and/or local code. 
 

OWNER/USER RESPONSIBILITIES 

It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and 
operate StreamLine Luminaires in such a manner as to comply with all state and local laws, ordinances, 
regulations, and the American National Standard Institute Safety Code. 
 

 

Summary of Contents for StreamLine








Reviews: