OPTO-EDU A63.7015 Instruction Manual Download Page 16

Page: 16 / 16

Opto-Edu 16 / 16 [email protected]

⚫

Check if the " A63.7015 (A63.7006)" device is turned on

⚫

Check if necessary, programs are executing

⚫

Check if your computer has virus.

2.3. Communication failure

Problem

The error message "Cannot find Active Scan facility" pops up

Reason

Poor USB cable connection between device and computer

Solution

Reconnect the USB cable

2.4, Vacuum Failure

Problem

A continuous beep of "BB" is emitted from the internal motherboard of the device during
the vacuuming process

Reason

⚫

The vacuum pump tube between the mechanical vacuum pump and
A63.7015/A63.7006 is not properly connected

⚫

Mechanical vacuum pump failure

⚫

Molecular pump failure

⚫

The sample compartment door is not fully closed

Solution

⚫

Check the connection status of the vacuum pump between the mechanical vacuum
pump and A63.7015/A63.7006

⚫

Close the sample compartment door tightly when vacuuming

⚫

Replacing the vacuum pump oil in the mechanical vacuum pump

Summary of Contents for A63.7015

















Search results

Summary of Contents for A63.7015

Reviews:

Related manuals for A63.7015

Brands by name

Popular brands

OPTO-EDU A63.7015, Instruction Manual

Search results

Summary of Contents for A63.7015

Reviews:

Related manuals for A63.7015

Brands by name

Popular brands