background image

Safety

Version 1.0.1 - 2020-11-12

3

Translation of original instruction

GU35P

EN

GU35P

_GB

.f

m

explains the meaning and use of the warning notes included in these operating instructions,

defines the intended use of the polishing machine,

points out the dangers that might arise for you or others if these instructions are not 
observed,

informs you about how to avoid dangers.

In addition to these operating instructions, please observe

the applicable laws and regulations,

the statutory provisions for accident prevention,

the prohibition, warning and mandatory signs as well as the warning notes on the polishing 
machine.

Always keep this documentation close to the polishing machine.

1.1

Safety instructions (warning notes)

1.1.1

Classification of hazards

We classify the safety warnings into different categories. The table below gives an overview of
the classification of symbols (ideogram) and the warning signs for each specific danger and its
(possible) consequences.

Symbol

Alarm expression

Definition / consequence

DANGER!

Impending danger that will cause serious injury or death to people.

WARNING!

A danger that can cause serious injury or death.

CAUTION!

A danger or unsafe procedure that can cause personal injury or damage 
to property.

ATTENTION!

Situation that could cause damage to the polishing machine and 
product, as well as other types of damage.

No risk of injury to persons.

INFORMATION

Practical tips and other important or useful information and notes.

No dangerous or harmful consequences for people or objects.

Summary of Contents for OPTIpolish GU 35P



















Reviews: