background image

 

10 

ventilation  and  to  access  cable  connectors.  Consider  following  steps  to  install  the  RPS 
system on a flat surface. 
 

 

Set the RPS Power Series RPS on the flat surface and check for proper ventilation 
and air flow. 

 

Allow at least 2 inches (5.1 cm) on each side for proper ventilation and 5 inches 
(12.7 cm) at the back for AC and DC power-cord clearance. 

 

Attach rubber feet on the bottom of the chassis to keep the unit from slipping. 

 

Installing the RPS Power Supply in a Rack 
 

The  RPS  Power  Supply  can  be  installed  in  most  standard  19-inch  racks.  Consider 
following steps to install RPS Power Series RPS in rack. 
 

 

Use appropriate size screws to attach the RPS system to the 19-inch rack. 

 

Position the RPS Power Series RPS in the rack and align the oval shaped holes on 
the side of the RPS with the holes in the rack. 

 

Insert and tighten two screws appropriate for  your rack through each of the oval 
shaped holes on the side of the RPS. 

 

To Operate the RPS Power Supply after Installation 

 

Model  RPS5412  may  be  installed  in  environments  that  meet  the  environmental 
characteristics specified in Chapter 2. 

It is recommended that sufficient ventilation gap be 

provided above or below the RPS unit for proper air flow.  

 

Once the RPS (redundant power supply) is mounted in the rack, it should be connected to 
a  switch 

(that  only  requires  –52VDC  or  +12VDC  power)

,

  and  has  a  DC  connector 

located on rear panel as shown: 
 
 
 
 

 

 
 
 
 
 
 

 
 
 
 
  

 

 
 

 

The figure shows where to connect the Optimal Power® RPS Model RPS5412 on the 
NETGEAR® switch. 

 

Note: The location of the redundant power supply connector on your switch may differ from 

the illustration

.  

 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RPS 

 

DC Connector on NETGEAR® 
switches for Optimal Power

®

 RPS 

Power Supply Series

™ RPS 

 

DC Connector on the 
switches  is  behind  a 
metal cover plate  

 

NETGEAR® Switch

 

RPS Connector 

 

All manuals and user guides at all-guides.com

Summary of Contents for RPSC5412

















Reviews: