OPTILAB BCB-4 User Manual Download Page 13

BCB-

4 User’s Manual 

Page 10 of 14 

 

Optilab, LLC

 

600 E. Camelback Road, Phoenix, AZ  85012 
Phone: (602) 343-1496, Fax: (602) 343-1489, Email:  [email protected] 

6.  Service and Support 

 

6.1  Warranty 

Optilab, LLC guarantees its BCB-4 unit to be free of defects for 1 year from the 
date of shipment.  The guarantee does not cover any damages resulting from 
the  misuse  or  improper  handling  of  the  equipment,  or  any  incidental  or 
consequential  loss.    Note  that  the  warranty  will  be  void  upon  any  attempt  to 
open or to fix the equipment by the user without prior approval of Optilab, LLC 

 

6.2  Service and Calibration 

Your BCB-4 unit has been designed to provide years of trouble-free operation.  
No  internal  maintenance  is  required  provided  that  the  equipment  is  properly 
handled,  operated,  and  kept  away  from  contamination.    For  any  questions 
regarding  the  operation  and  performance  of  the  unit,  please  contact  Optilab, 
LLC at: 

 

Optilab, LLC 

 

600 E. Camelback Road 
Phoenix, AZ  85012 

 

Phone: 

(602) 343-1496

 

Fax: 

(602) 343-1489 

Email:  

[email protected]

 

 

 

 

 

Summary of Contents for BCB-4


















Reviews: